Emerson VSG & VSSG Specifications Page 90
- Page / 162
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
7 – 8
Section 7 • Compressor Control Setpoints
Single Screw Compressor PLC Operation Manual • Vilter/Emerson • 35391CM
will be energized after the compressor main motor
stops, if installed.
• Oil Drain Solenoid ON Time (at Stop): Amount of
time the oil drain solenoid will be energized after the
compressor main motor stops, if installed.
OIL SEPARATOR HEATERS
• Defi nes separator oil temperature setpoints to con-
trol the oil separator heaters.
PART TIME OIL PUMP
• If selected, defi nes the pressure ratios at which the oil
pump will stop above and re-start below.
LOAD LIMITS
For more information on load limits and forced unload-
ing, see Section 2 Operational Descriptions.
• Low Suction Pressure Inhibit Loading: compressor
will not be allowed to load if Suction Pressure falls be-
low this setpoint.
• Low Suction Pressure Unload At: Compressor will be-
gin continuously unloading if Suction Pressure falls
below this setpoint.
• Low Suction Pressure Unload To: If forced unloading
is active, the compressor will unload continuously un-
til Suction Pressure reaches this setpoint.
• High Discharge Pressure Inhibit Loading: compressor
will not be allowed to load if Discharge Pressure rises
above this setpoint.
• High Discharge Pressure Unload At: Compressor will
begin continuously unloading if Discharge Pressure
rises above this setpoint.
• High Discharge Pressure Unload To: If forced unload-
ing is active, the compressor will unload continuously
until Discharge Pressure reaches this setpoint.
• High Motor Amps Inhibit Loading: compressor will
not be allowed to load if Main Motor Amperage rises
above this setpoint.
• High Motor Amps Unload At: Compressor will begin
continuously unloading if Main Motor Amperage ris-
es above this setpoint.
• High Motor Amps Unload To: If forced unloading is
active, the compressor will unload continuously until
Main Motor Amperage reaches this setpoint.
VOLUME SLIDE ADJUSTMENT
• Volume Slide Adjustment Factor: Offset that will be
applied to the calculated volume slide target.
• Capacity Slide Range Adj. Factor is Applied: The
Volume Slide Adjustment Factor will be applied when
capacity slide valve position is within the defi ned
range.
MAIN MOTOR FLA
• This is a convenience calculation to aid in setting mo-
tor amps load limit setpoints.
- Single Screw Compressor PLC 1
- Important Message 4
- Table of Contents 5
- List of Tables and Figures 10
- HOW TO USE THIS MANUAL 13
- ADDITIONAL IMPORTANT NOTES 13
- Glossary of Terms 14
- 23 678 5 19
- Wiring Requirements 21
- Overview 23
- Operational Descriptions and 24
- Diagrams 24
- COMPRESSOR STARTUP SEQUENCE 25
- AUTO START-STOP 26
- ANTI-RECYCLE 26
- CAPACITY SLIDE CONTROL 26
- OPERATING MODES 30
- DISCHARGE 31
- PRESSURE 31
- SUCTION 31
- VFD CAPCITY CONTROL 32
- VOLUME SLIDE CONTROL 32
- SAFETIES 32
- EMERGENCY STOP 32
- OIL HEATERS 33
- OIL DRAIN SOLENOID 33
- 2-WAY OIL MIXING VALVE 34
- OIL INJECTION VALVE 34
- OIL COOLER TEMPERATURES 35
- OIL COOLER STANDBY HEATER 35
- EVAPORATIVE CONDENSER 37
- OIL COOLER 38
- CONDENSER 39
- WATER COOLED GAS AFTERCOOLER 40
- WATER COOLED CONDENSER 41
- LIQUID INJECTION VALVE 42
- VPLUS LIQUID INJECTION PUMP 43
- DISCHARGE RECYCLE VALVE 44
- ECONOMIZER SOLENOID(S) 45
- HOTGAS BYPASS SOLENOID 45
- VENTURI OIL RECOVERY 45
- GAS SCRUBBERS 45
- BUILDING ENCLOSURE DEVICES 46
- PERIODIC SLIDE VALVE EXERCISE 46
- Section 3 • Overview Screens 47
- 3 – 8 / Blank 54
- Section 4 • HMI Navigation 55
- 4 – 10 / Blank 64
- DATE AND TIME 66
- REMOTE OPERATION 66
- PANELVIEW CONFIGURATION 68
- INITIAL RUNNING DATA 68
- DEVICE NAMES 68
- BACK TO MENU 68
- Editing Device Names 69
- INSTRUMENTATION 70
- ALARM AND TRIP 71
- Calibration Main Screen 73
- Pressure Calibration Screen 74
- CALIBRATE PRESSURE INSTRUMENT 75
- OPTION 1 75
- OPTION 2 75
- Slide Calibration Screen 78
- Figure 6-8. Actuator Assembly 80
- Figure 6-9. Photo-chopper 81
- 6 – 10 / Blank 82
- Setpoints and Control Screens 83
- Compressor Control Setpoints 84
- MAIN MOTOR VFD 86
- DISCHARGE PRESSURE CONTROL 87
- CAPACITY SLIDE VALVE 87
- AUTO START/STOP 88
- ANTI-RECYCLE 89
- START UP 89
- SHUT DOWN 89
- PART TIME OIL PUMP 90
- LOAD LIMITS 90
- VOLUME SLIDE ADJUSTMENT 90
- MAIN MOTOR FLA 90
- OIL SEPARATOR HEATERS 90
- 7 – 10 / Blank 92
- Alarm and Trip Setpoints 93
- Oil Mixing Valve Screen 95
- Aftercooler Screens 98
- Condenser Screens 101
- Volume Slide Details Screen 107
- Start Menu Popup Screen 108
- IO/Comms Diagnostics Screen 109
- Event List Screen 110
- 10 – 6 / Blank 114
- Alarm Listing 115
- Alarm Message Cause(s) Notes 117
- Trip Listing 123
- Trip Message Cause(s) Notes 124
- Status Message Notes 130
- Troubleshooting 134
- Communication with a Central 135
- Controller/DCS 135
- Compressor PLC 135
- Pressure Units 136
- Temperature Units 136
- Alarm and Trip Data 142
- Interface Tag Description 143
- Status Data 150
- States of Discrete I/O 154
- Table 12-8. State Indicator 159
- Table 12-9. Mode Indicator 159
Related products and manuals for Air compressors Emerson VSG & VSSG
(10 pages)© 2020, manymanuals.com. All rights reserved. | 0.767 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals