Emerson VSG & VSSG Specifications Page 123
- Page / 162
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
11 – 9
Section 11 • Alarms, Trips, Status Information & Troubleshooting
Single Screw Compressor PLC Operation Manual • Vilter/Emerson • 35391CM
Trip Message Cause(s) Notes
(T001) Trip: MCR Not Energized/E-
Stop Active
Emergency Stop Button on PLC
panel Pressed, Loss of Power
(T002) Trip: PLC to Central Comms
Faulted
Loss of Communication with DCS/
Central - Settable Communications
Watchdog Timer Expired. (Action on
Comm Failure = Trip)
Watchdog Active if Control by
Communications is selected
(T003) Trip: High Main Motor Amps Main Motor Amps exceeds Motor
Amps High Trip setpoint.
(T004) Setpoint out of Range - See
Menu Screen
(T005) Trip: False Start Detected Main motor was detected running
when not commanded to run.
(T006) Trip: Low Separator Oil Level Oil Separator Level Switch has
opened indicating drop in Separator
Oil Level. (Trip action Selected)
Active if Oil Separator Level Switch
Selected.
(T007) Trip: Faulted I/O Module
Connection or Module Type
(T008) Trip: Main Motor Starter Fault Main Motor Starter Fault Contact has
opened.
(T009) Trip: Main Motor Feedback
Fault/Overload
Main Motor is commanded to run,
Running confi rmation not received.
(T010) Trip: Main Motor Shunt Trip
Activated
Shutdown Active.
Note: Output energized to activate
a power removal device to protect
the compressor when a false start is
detected.
(T011) Trip: Low Suction
Temperature
Suction Temperature falls below
"Suction Temperature" Low Trip
Setpoint.
(T012) Trip: High Discharge
Temperature
Discharge Temperature exceeds
"Discharge Temperature" High Trip
Setpoint.
(T013) Trip: Low Oil Separator
Temperature - Start
Separator Oil Temperature is Below
"Separator Oil Temperature - Start"
Low Trip Setpoint when compres-
sor is off or Oil Separator Start-Run
Timer has not expired.
(T014) Trip: Low Oil Separator
Temperature - Run
Separator Oil Temperature is Below
"Separator Oil Temperature - Run"
Low Trip Setpoint After Oil Separator
Start-Run Timer has expired.
Trip Listing
Table 11-2. Trip Listing
- Single Screw Compressor PLC 1
- Important Message 4
- Table of Contents 5
- List of Tables and Figures 10
- HOW TO USE THIS MANUAL 13
- ADDITIONAL IMPORTANT NOTES 13
- Glossary of Terms 14
- 23 678 5 19
- Wiring Requirements 21
- Overview 23
- Operational Descriptions and 24
- Diagrams 24
- COMPRESSOR STARTUP SEQUENCE 25
- AUTO START-STOP 26
- ANTI-RECYCLE 26
- CAPACITY SLIDE CONTROL 26
- OPERATING MODES 30
- DISCHARGE 31
- PRESSURE 31
- SUCTION 31
- VFD CAPCITY CONTROL 32
- VOLUME SLIDE CONTROL 32
- SAFETIES 32
- EMERGENCY STOP 32
- OIL HEATERS 33
- OIL DRAIN SOLENOID 33
- 2-WAY OIL MIXING VALVE 34
- OIL INJECTION VALVE 34
- OIL COOLER TEMPERATURES 35
- OIL COOLER STANDBY HEATER 35
- EVAPORATIVE CONDENSER 37
- OIL COOLER 38
- CONDENSER 39
- WATER COOLED GAS AFTERCOOLER 40
- WATER COOLED CONDENSER 41
- LIQUID INJECTION VALVE 42
- VPLUS LIQUID INJECTION PUMP 43
- DISCHARGE RECYCLE VALVE 44
- ECONOMIZER SOLENOID(S) 45
- HOTGAS BYPASS SOLENOID 45
- VENTURI OIL RECOVERY 45
- GAS SCRUBBERS 45
- BUILDING ENCLOSURE DEVICES 46
- PERIODIC SLIDE VALVE EXERCISE 46
- Section 3 • Overview Screens 47
- 3 – 8 / Blank 54
- Section 4 • HMI Navigation 55
- 4 – 10 / Blank 64
- DATE AND TIME 66
- REMOTE OPERATION 66
- PANELVIEW CONFIGURATION 68
- INITIAL RUNNING DATA 68
- DEVICE NAMES 68
- BACK TO MENU 68
- Editing Device Names 69
- INSTRUMENTATION 70
- ALARM AND TRIP 71
- Calibration Main Screen 73
- Pressure Calibration Screen 74
- CALIBRATE PRESSURE INSTRUMENT 75
- OPTION 1 75
- OPTION 2 75
- Slide Calibration Screen 78
- Figure 6-8. Actuator Assembly 80
- Figure 6-9. Photo-chopper 81
- 6 – 10 / Blank 82
- Setpoints and Control Screens 83
- Compressor Control Setpoints 84
- MAIN MOTOR VFD 86
- DISCHARGE PRESSURE CONTROL 87
- CAPACITY SLIDE VALVE 87
- AUTO START/STOP 88
- ANTI-RECYCLE 89
- START UP 89
- SHUT DOWN 89
- PART TIME OIL PUMP 90
- LOAD LIMITS 90
- VOLUME SLIDE ADJUSTMENT 90
- MAIN MOTOR FLA 90
- OIL SEPARATOR HEATERS 90
- 7 – 10 / Blank 92
- Alarm and Trip Setpoints 93
- Oil Mixing Valve Screen 95
- Aftercooler Screens 98
- Condenser Screens 101
- Volume Slide Details Screen 107
- Start Menu Popup Screen 108
- IO/Comms Diagnostics Screen 109
- Event List Screen 110
- 10 – 6 / Blank 114
- Alarm Listing 115
- Alarm Message Cause(s) Notes 117
- Trip Listing 123
- Trip Message Cause(s) Notes 124
- Status Message Notes 130
- Troubleshooting 134
- Communication with a Central 135
- Controller/DCS 135
- Compressor PLC 135
- Pressure Units 136
- Temperature Units 136
- Alarm and Trip Data 142
- Interface Tag Description 143
- Status Data 150
- States of Discrete I/O 154
- Table 12-8. State Indicator 159
- Table 12-9. Mode Indicator 159
Related products and manuals for Air compressors Emerson VSG & VSSG
(10 pages)© 2020, manymanuals.com. All rights reserved. | 0.982 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals