Emerson Liebert iCOM User Manual Page 137
- Page / 192
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
Service Menu Parameters
127 Liebert
®
iCOM
®
S138 DT2 (Room/FC Fluid) Value—Sets the delta between the actual temperature and fluid
temperature that must be met before free-cooling will occur.
Example: Actual Temperature = 75°F
Free-cooling Temperature = 70°F
DT2 Value = 4
Since the difference between the free-cooling fluid and the actual temperature is 5°F and the DT2
value is set to 4°F, then free-cooling would be utilized.
S139 Minimum CW Temp—Enables the temperature at which free-cooling can operate
independently without assistance of the compressor circuit(s).
S140 Minimum CW Temp Value—Sets the water temperature at which 100% free-cooling can be
provided to handle the full room load. When the fluid temperature is below this setting, then the
compressors will no longer turn On until the water temperature is above the minimum CW Temp.
S141 Lockout FC at FC Fluid below—Prevents frost from building up on the free-cooling pipes
when the outdoor ambient is extremely low by turning Off the free-cooling circuit when the water
temperature is too low.
Figure 108 Setpoints screen, page 5 of 9
S146 Fan Control Sensor—Controls the fan speed for modulation. Options for this setting are
Supply, Return, Remote, and Manual Mode.
If manual mode is selected, then the fan speed can be controlled from the local display or through a
building management system.
S147 Fan Setpoint—Activated when a temperature sensor is being used to control the fan speed. If
the same sensor is used for temperature control and fan speed control, then this value will reflect the
same setpoint as the temperature control setpoint. Manual mode uses the Fan Speed STD for control.
S148 Fan Temp Control Type—Sets the type of control the unit will use to control fan speed.
PI controls gain is set in the Temp Prop / Integral parameter.
PI control will operate the fan speed so that the actual temperature of the fan control sensor is
equal to the fan temp setpoint. If proportional only is selected, the fan will change “ONLY” based
on the deviation from setpoint which will allow the actual temp to settle higher than setpoint.
- 2
- TABLE OF CONTENTS 3
- 1.0 INTRODUCTION 11
- 2.1 System Screen 14
- 5Liebert 15
- 2.2 Main Unit Screen 16
- 2.3.2 Accessing Submenus 17
- Display Filtering 19
- 2.3.3 Entering a Password 20
- Figure 14 User menu icons 23
- Table 2 User menu icons 23
- Figure 15 Service menu icons 24
- Table 3 Service menu icons 24
- 3.0 OPERATION 26
- Autorestart 27
- Loss of Power Alarm 27
- Minimum Fan Speed 29
- Operation 30
- Low-Pressure Time Delay 31
- Advanced DX Freeze Protection 31
- Pump Down 32
- High Pressure Alarm 32
- 23 Liebert 33
- Settings 34
- 25 Liebert 35
- 3.2.2 Compressor Control 36
- Compressor Proportional Bands 36
- 27 Liebert 37
- 3.2.3 Chilled Water Control 38
- 29 Liebert 39
- 31 Liebert 41
- Cooling—Free-Cooling 42
- Dual-Cooling Source 42
- DETAIL CDETAIL B 43
- DETAIL D 43
- FRONT VIEW 43
- DETAIL E 44
- 35 Liebert 45
- 3.4 Liebert Air Economizer 46
- Operation 46
- 37 Liebert 47
- 3.4.2 Liebert Air Economizer 48
- System Overview 48
- (Not by 49
- Emerson) 49
- Out of Service 50
- 41 Liebert 51
- 43 Liebert 53
- 3.5.2 SCR Reheat 57
- Tight Mode 57
- 3.6.1 Humidification 59
- Infrared Humidifier 59
- 3.6.2 Dehumidification 60
- Dehumidification Low Limit 60
- . If the proportional 63
- Setting Up PI control 64
- 3.8 Supply Control 66
- 3.9.1 Operation 67
- Temperature Compensation 68
- Racks with Equipment 73
- Figure 59 S190 Limit 75
- Figure 60 S190 Control 75
- 67 Liebert 77
- 3.10.2 User Inputs 80
- and Liebert DS 81
- Air-Cooled Units 81
- 3.10.4 Liebert iCOM-DO 82
- Calculating Unit Wellness 84
- 75 Liebert 85
- 4.0 TEAMWORK 86
- 4.2.2 No Teamwork 87
- 4.2.3 Teamwork Mode 1 87
- 4.2.4 Teamwork Mode 2 88
- Fixed Speed 89
- Variable Speed 89
- Teamwork 90
- 4.2.6 Hardware Setup 91
- 4.3.2 DIP Switch Settings 92
- Unterminated 94
- Terminated 94
- 85 Liebert 95
- Grounded CANbus Cable 97
- 4.3.8 Software Setup 99
- 4.3.9 Standby—Rotation 99
- Standby and Cascade 100
- 91 Liebert 101
- Small Displays 104
- Large Displays 104
- 95 Liebert 105
- Small Graphics Display 106
- Liebert iCOM 107
- I/O Board 107
- Graphics Display 108
- (Rear View) 108
- Optional Large 108
- SITESCAN 110
- 6.1 Terminals 77 and 78 111
- via 77/78 112
- 7.0 USER MENU PARAMETERS 113
- User Menu Parameters 114
- 105 Liebert 115
- 7.2 User-Graphic Menu Screens 116
- Event Log 117
- View Network 117
- 109 Liebert 119
- 111 Liebert 121
- 113 Liebert 123
- Active Alarms 125
- 117 Liebert 127
- 119 Liebert 129
- 121 Liebert 131
- 8.0 SERVICE MENU PARAMETERS 132
- Service Menu Parameters 133
- 123 Liebert 133
- 125 Liebert 135
- 127 Liebert 137
- 129 Liebert 139
- 131 Liebert 141
- 133 Liebert 143
- 135 Liebert 145
- 137 Liebert 147
- 139 Liebert 149
- 141 Liebert 151
- 143 Liebert 153
- 145 Liebert 155
- 147 Liebert 157
- 149 Liebert 159
- Set Alarm Screens, Pages 4-10 160
- 151 Liebert 161
- 153 Liebert 163
- 155 Liebert 165
- 157 Liebert 167
- 159 Liebert 169
- 161 Liebert 171
- 163 Liebert 173
- 165 Liebert 175
- 167 Liebert 177
- 169 Liebert 179
- 171 Liebert 181
- 9.0 MONITORING POINTS 187
- Example of points generated 188
- Monitoring Points 189
- 179 Liebert 189
- Technical Support / Service 192
- Locations 192
© 2020, manymanuals.com. All rights reserved. | 0.788 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals