Emerson 3051S Specifications Page 122
- Page / 188
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
10
Reference Manual
00809-0100-4803, Rev DA
Section 5: Troubleshooting
April 2013
Troubleshooting
Table 5-1. Diagnostic message troubleshooting
LCD Messages Host Diagnostic Message Possible Problems Recommended Actions
AP GP LIMIT Static Pressure Out of Limits The Static Pressure is exceeding the
sensor limits.
Verify process conditions are within the
sensor limits.
BOARD COMM ERROR Feature Board Communication Error The feature board electronics are
experiencing communication
problems. This problem may be
temporary and could clear
automatically.
Cycle power to the device. If the problem
persists, replace the feature board
electronics.
CURR SAT Primary Variable Analog Output
Saturated
The primary variable has exceeded
the range points defined for the 4-20
mA analog output signal. The analog
output is fixed at the high or low
saturation point and is not
representative of the current process
conditions.
Verify the process conditions and modify
the Analog Range Values if necessary.
DP LIMIT Differential Pressure Out of Limits The Differential Pressure is exceeding
the sensor limits.
Verify that the process conditions are within
the sensor limits.
FAIL BOARD ERROR Feature Board Error The feature board electronics have
detected an unrecoverable failure.
Replace the feature board electronics.
FAIL PT ERROR Process Temperature Sensor Failure The process temperature sensor has
failed or is incorrectly wired.
Check the sensor wiring and fix any shorts
or open connections.
If the sensor wiring is correct, check the PT
sensor and replace if necessary. If the
problems persists, replace the feature
board electronics.
FAIL SENSOR ERROR Sensor Module Failure The SuperModule assembly is
providing measurements that may no
longer be valid.
Verify the Sensor Module Temperature is
within the operating limits of the
transmitter. Replace SuperModule
assembly if necessary.
FLOW CONFIG Updating Flow Configuration - Flow
Values Constant
A flow Configuration is currently
being downloaded to the transmitter.
During the download, the flow output
will be fixed at the last calculated
value. Once the download is
complete the transmitter will resume
live calculations.
No action is required. Please wait until the
flow configuration download is complete
before performing other configuration
tasks.
FLOW INCOMP ERROR Energy Invalid for Flow Configuration The Energy Flow variable is not
compatible with the current flow
configuration but is mapped to the
totalizer, a process variable, or a burst
variable.
These discrepancies can be fixed with the
following actions:
• Verify configuration for the fluid type
supports Energy Flow calculation.
• Do not specify Energy Flow for the
totalizer, process variables or burst
variables unless the transmitter has a
compatible flow configuration.
FLOW INCOMP ERROR Static Pressure Sensor Missing A static pressure sensor is needed for
the current flow configuration.
Download a flow configuration that is
compatible with the sensors equipped in
the device or replace the module with a
model that includes a static pressure
sensor.
FLOW INCOMP ERROR Flow Configuration Download Error The flow configuration did not
successfully download to the
transmitter.
Redownload the flow configuration using
the Engineering Assistant software.
FLOW LIMIT Flow Output Out of Limits The flow output value is exceeding
the flow rate operating limits.
Verify the process conditions, and modify
the flow configuration parameters and
operating ranges as needed.
FLOW LIMIT Energy Flow Out of Limits The energy flow value is exceeding
the flow rate operating limits.
Verify the process conditions, and modify
the flow configuration parameters and
operating ranges as needed.
LCD UPDATE ERROR LCD Update Error The LCD is not receiving updates from
the feature board electronics.
Examine the LCD Connector and reset the
LCD.
If the problem persists, first replace the LCD
then replace the feature board electronics if
necessary.
- Rosemount 3051S MultiVariable 1
- Transmitter 1
- Contents 5
- Table of Contents 6
- 5Section 5: Troubleshooting 7
- Section 1 Introduction 9
- 1.2 Models covered 10
- 1.3 Service support 10
- Section 2 Installation 11
- 2.2.1 Warnings 12
- 2.4 Installation procedures 13
- 2.4.2 Mounting considerations 14
- LCD display rotation 15
- Feature board side of housing 15
- Cover installation 15
- Conduit entry threads 15
- Cover jam screw 16
- Process flange orientation 16
- 2.4.3 Mount the transmitter 17
- Flange bolts 18
- Mounting requirements 19
- 2.4.4 Process connections 20
- ROSEMOUNT 3051S / 3051 / 2051 21
- Impulse piping considerations 22
- Surges/transients 25
- Signal wire grounding 26
- 2.4.7 Grounding 27
- 305 INTEGRAL 29
- COPLANAR 29
- 305 INTEGRAL TRADITIONAL 29
- 304 TRADITIONAL 29
- 304 WAFER 29
- Section 2: Installation 34
- Installation 34
- Section 3 Configuration 35
- 3.2 Safety messages 36
- Connecting to a PC 38
- 3.4 Flow configuration 39
- Online and offline mode 40
- 3.4.4 Preferences 42
- 3.4.6 Fluid properties 46
- 3.4.8 Save / send 49
- Saving a configuration 51
- Sending a saved configuration 51
- Natural gas 52
- Custom gas 54
- Custom liquid [Density (T)] 55
- Units of measure 57
- 3.6.1 Model identification 60
- 3.6.2 Alarm and saturation 60
- 3.6.3 Variable mapping 62
- 3.6.4 LCD display 63
- 3.6.5 Communication setup 64
- Burst mode 65
- Enabling burst mode 65
- Choosing a burst option 66
- Multidrop communication 66
- Loop current mode 67
- 3.7 Variable configuration 69
- Time conversion example: 73
- 3.7.2 Energy rate 75
- Energy conversion example: 77
- Section 3: Configuration 79
- Configuration 79
- 3.7.3 Totalizer 81
- Totalizer conversion example: 83
- 3.7.4 Differential pressure 84
- 3.7.5 Static pressure 85
- 3.7.6 Process temperature 86
- 3.7.7 Module temperature 87
- 3.7.8 Analog output 88
- (page 1) 91
- (page 2) 92
- 3.8.5 475 Fast keys 95
- Function Fast Key Sequence 96
- 4.1 Overview 99
- 4.2 Safety messages 100
- 4.3 Transmitter calibration 101
- 4.3.2 Sensor trim overview 102
- Zero trim 103
- Upper and lower sensor trim 103
- Calibration type 104
- Recall factory trim 104
- Last DP sensor trim point 104
- 4.3.6 Analog calibration 108
- Analog output loop test 109
- 00809-0100-4803, Rev DA 110
- April 2013 110
- 4.5 Process variables 111
- 4.5.2 All variables tab 112
- Field device labels 113
- Remove the feature board 114
- Black Rubber V-Seal 115
- 4.6.3 Terminal block 116
- 4.6.4 LCD display 117
- 4.6.5 Flange and drain vent 117
- 4.6.6 SuperModule assembly 119
- Reference Manual 120
- Operation and Maintenance 120
- Section 5 Troubleshooting 121
- Section 5: Troubleshooting 122
- Troubleshooting 122
- Symptom Corrective Actions 124
- Symptom Corrective Action 128
- Reference Data 131
- Total performance 132
- Long term stability 133
- Warranty 133
- Ambient Temperature effect 134
- Line Pressure effect 135
- Mounting Position Effects 135
- Vibration effect 135
- Power supply effect 136
- Range and sensor limits 137
- 4–20 mA/HART 138
- Overpressure limits 139
- Static Pressure limit 139
- Burst Pressure limits 140
- Temperature limits 140
- Humidity limits 140
- Volumetric displacement 141
- Failure mode alarm 141
- A.1.3 Physical specifications 142
- Sensor module fill fluid 143
- Cover O-rings 143
- A.2 Dimensional drawings 145
- Pipe Mount Panel Mount 146
- Appendix A: Reference Data 147
- 3.56 Max open 148
- (90 Max open) 148
- A.3 Ordering information 149
- 2-14 NPT flange adapter ★ 152
- 2 SST flange adapter 152
- A.4 Accessories 157
- A.5 Exploded view diagram 158
- A.6 Spare Parts 159
- North American certifications 166
- European certifications 166
- Japanese certifications 167
- INMETRO certifications 168
- China (NEPSI) certifications 168
- IECEx certifications 169
- B.5 Installation drawings 171
- Product Certifications 172
- B.5.3 GE / GM option NEMA 4X 181
Related products and manuals for Measuring, testing & control Emerson 3051S
(4 pages)© 2020, manymanuals.com. All rights reserved. | 0.636 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals