Emerson Liebert ICOM-DO User Manual Page 31
- Page / 172
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
Operation
23 Liebert
®
iCOM
®
for Liebert DSE
™
Figure 19 Energy efficiency—No bypass air, EC fan damper
3.1.3 General Compressor Operation
Low-Pressure Time Delay
When the compressor starts, the low-pressure input is ignored for a selected period of time based on
the setting of the Low Pressure Alarm Delay (Service Menu, Options Setup). This time is usually set
to 3 minutes on air-cooled units, and to 0 or 1 minute on water cooled units. When this time is
expired, a second timer starts to operate if the low-pressure input is active. This second timer is active
during normal compressor operation to avoid compressor trips due to bubbles in the refrigerant or
other influences creating short trips of the low-pressure device. The low-pressure device input is
ignored if the compressor is not operating.
Advanced DX Freeze Protection
Applying fan speed to direct expansion systems generates the issue of how to avoid freezing
condensate on the coil when the unit operates below 100% fan speed. Liebert iCOM's advanced freeze
protection provides the ability to predict freeze conditions and correct this condition automatically by
adjusting the fan speed and compressor capacity.
Compressor Type Support
• Digital scroll (all sizes)
• Tandem Scroll
Freeze Protection
• Fan and compressor will override sensors when freezing is detected
• Fan ramps up first, then compressor unloads
Pump Down Operation
The Liebert DSE is not equipped with pump down mode due to the microchannel condenser.
NOTE
Low-pressure condition could be read through contacts or through pressure transducers with
threshold setting.
- for Liebert DSE 1
- 2
- TABLE OF CONTENTS 3
- 1.0 INTRODUCTION 9
- 2.1.1 System Screen 12
- 5Liebert 13
- Unit Screen 14
- EconoPhase circuit 16
- 2.2.1 Control Interface 17
- 2.2.2 Accessing Submenus 17
- Display Filtering 18
- Liebert iCOM Display Readout 18
- Accessing Submenus 19
- 2.2.3 Entering a Password 20
- Table 3 User menu icons 23
- Table 4 Service menu icons 25
- 3.0 OPERATION 27
- Autorestart 28
- Loss of Power Alarm 28
- Minimum Fan Speed 30
- 3.1.2 Back-Draft Fan Damper 30
- Low-Pressure Time Delay 31
- Advanced DX Freeze Protection 31
- Pump Down Operation 31
- High Pressure Alarm 32
- Operation 33
- 25 Liebert 33
- 3.2 Temperature Control 34
- . If the proportional 35
- 3.2.1 Setting Up PI Control 36
- Temperature Deadband 36
- 3.2.2 Compressor Control 36
- 29 Liebert 37
- System 1 System 2 38
- 3.3.3 Tandem Operation 39
- Additional Reheat Rules 40
- 3.5 Humidity Control 41
- 3.5.1 Humidity Control Types 42
- 3.5.2 Humidification 43
- Infrared Humidifier 43
- 3.5.3 Dehumidification 44
- Dehumidification Low Limit 45
- 39 Liebert 47
- Dehumidification Operation 48
- 41 Liebert 49
- 43 Liebert 51
- Temperature Compensation 52
- Setpoint Manipulated Variable 56
- Controlled Variable 56
- and Liebert 57
- 3.8.1 CANbus Failure 58
- EEV Battery Backup 59
- 3.8.4 Liebert MC 59
- Low Noise / Fan Reversal 60
- 3.8.6 Liebert EconoPhase 61
- 57 Liebert 65
- Event Description 68
- 3.9.2 User Inputs 70
- Table 16 Customer inputs 71
- 3.9.3 Analog Inputs 72
- 3.9.4 Liebert iCOM-DO 73
- Table 20 Event notifications 74
- Calculating Unit Wellness 76
- 69 Liebert 77
- 4.0 TEAMWORK 78
- 4.2.2 No Teamwork 79
- 4.2.3 Teamwork Mode 2 79
- Fixed Speed 80
- Variable Speed 80
- Teamwork 81
- 73 Liebert 81
- Figure 49 Remote sensors 82
- Figure 50 Sensor positioning 82
- 4.2.5 Hardware Setup 83
- 4.3.2 DIP Switch Settings 84
- Unterminated 86
- Terminated 86
- Grounded CANbus Cable 87
- 4.3.7 Software Setup 89
- 4.3.8 Standby—Rotation 90
- Standby and Cascade 90
- Liebert iCOM 95
- I/O Board 95
- Optional Large 95
- Graphics Display 95
- (Rear View) 95
- Liebert vNSA 96
- SITESCAN 97
- 7.0 USER MENU PARAMETERS 98
- 91 Liebert 99
- User Menu Parameters 100
- 7.2 User-Graphic Menu Screens 101
- Event Log 102
- View Network 102
- 95 Liebert 103
- 97 Liebert 105
- 99 Liebert 107
- Active Alarms 108
- 101 Liebert 109
- 103 Liebert 111
- 105 Liebert 113
- 8.0 SERVICE MENU PARAMETERS 114
- Service Menu Parameters 115
- 107 Liebert 115
- 109 Liebert 117
- 111 Liebert 119
- 113 Liebert 121
- 115 Liebert 123
- 117 Liebert 125
- 119 Liebert 127
- 121 Liebert 129
- 123 Liebert 131
- 127 Liebert 135
- 129 Liebert 137
- 131 Liebert 139
- 133 Liebert 141
- Set Alarm Screens, Pages 4-12 142
- 135 Liebert 143
- 137 Liebert 145
- 139 Liebert 147
- 143 Liebert 151
- 145 Liebert 153
- 147 Liebert 155
- 149 Liebert 157
- 151 Liebert 159
- 153 Liebert 161
- 155 Liebert 163
- 161 Liebert 169
- Technical Support / Service 172
- Locations 172
Related products and manuals for Networking Emerson Liebert ICOM-DO
(166 pages)
Networking Emerson FM-3 Specifications
(110 pages)
(110 pages)
Networking Emerson FM-3 User Manual
(8 pages)
(8 pages)
Networking Emerson Liebert CW User Manual
(136 pages)
(136 pages)
Networking Emerson Liebert FPC User Manual
(58 pages)
(58 pages)
Networking Emerson FM-3 User's Guide
(263 pages)
(263 pages)
Networking Emerson Mynah PLC-5 Datasheet
(18 pages)
(18 pages)
Networking Emerson X-web500 User Manual
(116 pages)
(116 pages)
Networking Emerson Mynah SLC-500 User's Guide
(131 pages)
(131 pages)
Networking Emerson X-web300 User Manual
(26 pages)
(26 pages)
© 2020, manymanuals.com. All rights reserved. | 0.597 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals