Emerson Liebert Remote Monitoring Panel User Manual Page 51
- Page / 144
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
System and Control Options
43 Liebert
®
Universal Monitor
™
9.0 SYSTEM AND CONTROL OPTIONS
The System and Control menu allows you to configure the Liebert Universal Monitor—setting up
inputs and outputs and an input/output matrix to trigger actions, the modem and pagers, and system
features such as date and time. This menu also provides a vehicle for manually changing the state of
an output to ON or OFF, clearing active alarms and deleting records from the Liebert Universal
Monitor’s alarm log, event log and trend logs.
The arrows
↑↓ are used to scroll through the menu. The Enter ↵ key is used to select the menu item
and enter new information. Table 20 shows characters that may be entered in labels and values.
The System and Control options require a password to prevent unauthorized users from making
changes to the system.
This section presents step-by-step instructions for each of the following:
• Login - enter the password
• Setup System - configure inputs, outputs, modem, pagers, system features
• Manual Output Ctrl - manually override automatic control of outputs; release the override
• Clear Alarms & Logs - clear active alarms; delete records from the alarm, event and trend logs
9.1 Login
Users must enter a password to access any of the system and control
options. The password consists of four characters (see Table 20 for
valid characters). (To set up or change the password, see 9.9.1 -
Change Password.)
To log in:
• From the Main Menu, use the arrows
↑↓ to choose System and
Control, then press Enter ↵, as shown at right.
• Use the arrows
↑↓ to choose System and Control, and press
Enter ↵. The Login menu appears.
• To enter your password:
• Use the arrows
↑↓ to choose a character.
• Press Enter ↵ to advance to the next character position.
• When finished, press Enter ↵ again.
The System and Control Menu appears next, with these options that
are described in the following sections:
• Setup System (Section 9.2 - Section 9.9)
• Manual Output Ctrl (Section 9.11)
•Clear Alarms & Logs (Section 9.12)
NOTE
For ease of understanding, this section uses the LCD interface to illustrate most instructions,
except for features that are available only through the Service Terminal Interface. All Service
Terminal Interface screens appear in Appendix A - Service Terminal Interface.
Table 20 Valid characters for data entry
Alphanumeric Special characters
A-Z, 0-9 space [ ] ^ _ ! " # $ % & ( ) * + - / , . ; < = > @
NOTE
If an alarm occurs while a user is logged on, the LCD backlight will flash and the audible
alarm will sound. To obtain specific information about the alarm, you must access the Active
Alarm screen (see 7.1 - View Active Alarms) or the Alarm Log (see 7.2 - View Alarm Log).
NOTE
If, after logging in, you press the ESC key to return to a previous screen that is not password-
protected, you must log in again, including entering your password if you wish to access
password-protected functions.
Main Menu
VIEW STATUS
> SYSTEM AND CONTROL
↑↓=NEXT
↵=SELECT
Login
LOGIN
AAAA
↑↓=SELECT ↵=NEXT/END
System & Control Menu
> SETUP SYSTEM
MANUAL OUTPUT CTRL
CLEAR ALARMS & LOGS
↑↓=NEXT
↵=SELECT
- Universal Monitor 1
- TABLE OF CONTENTS 3
- 7.0 VIEW STATUS OPTIONS 4
- 10.0 SPECIFICATIONS 5
- 1.0 INTRODUCTION 9
- ALL CIRCUITS; 10
- ALL CIRCUITS: 11
- 1.7 Controller Board Overview 12
- POWER INPUT 14
- RELAY OUTPUTS 14
- 1.9 LED Indicators 15
- K4K3K2K1 K5 K6 K7 K8 16
- 1.11 Typical Sequence 17
- 2.0 INSTALLATION - MAIN BOARD 18
- Required tools 19
- 2.2.1 Mounting the Panel 19
- 2.3.1 Mounting the Panel 20
- Input Power Connections 22
- Packing Contents 24
- 3.2.1 Mounting the Panel 25
- 3.3.1 Mounting the Panel 26
- 4.1 Wiring Specifications 28
- (BOTTOM) 29
- 4.3 Connecting Analog Inputs 30
- TB10: COMMS 31
- 4.5 EIA422 Liebert SiteScan 32
- Web Connector 32
- 5.1 Wiring Specifications 33
- S4 S3 S2 S1 34
- EIA485 + (to UM-) 34
- EIA485 - (to UM+) 34
- POWER INPUT RELAY OUTPUTS 35
- 29 Liebert 37
- 6.0 OVERVIEW OF MENUS 38
- 6.1 Opening Screen Overview 39
- 6.2 Main Menu Overview 39
- 6.3 LCD Menu Overview 39
- 7.1 View Active Alarms 41
- 7.2 View Alarm Log 42
- 7.3 View Event Log 43
- 7.4 View Trend Log 44
- 7.5 View Input Status 45
- 7.6 View Output Status 46
- 7.7 View Pager Numbers 47
- 9.1 Login 51
- ↑↓=NEXT ↵=SELECT 52
- ↑↓=SELECT ↵=NEXT/END 52
- 9.2 Setup System - Overview 53
- 9.3.5 Set Up Delay Time 55
- 9.5.3 Change Units Label 58
- 9.5.4 Change 4 mA Value 59
- 9.5.5 Change 20 mA Value 59
- 9.5.6 Change Offset Value 59
- 9.5.9 Change Low Setpoint 61
- 9.5.10 Change High Setpoint 61
- 9.5.11 Set Up Delay Time 62
- Supported Modem Settings 68
- Default Modem Settings 68
- Configuring the Modem 68
- 9.9.1 Change Password 77
- Change the Password 77
- 9.9.3 Setup Site ID 78
- 9.9.4 Connect Battery 78
- 9.9.8 Factory Defaults 84
- 9.11 Manual Output Ctrl 88
- 9.12 Clear Alarms & Logs 89
- 9.12.3 Clear the Event Log 90
- 9.12.4 Clear the Trend Logs 90
- 85 Liebert 93
- A.2.1 Connection Methods 94
- A.2.2 Create a Connection 95
- COM1 Port Setup 96
- Properties Setup 97
- ASCII Setup 97
- A.3 OVERVIEW OF MENUS 99
- A.4 VIEW STATUS MENUS 100
- A.4.1 View Active Alarms 101
- A.4.2 View Alarm Log 102
- A.4.3 View Event Log 103
- A.4.4 View Trend Log 104
- A.4.5 View Input Status 105
- A.4.6 View Output Status 106
- A.4.7 View Pager Numbers 107
- Main Menu 108
- Back Up Alarm Log File 109
- Back Up Event Log File 110
- Back Up Trend Log Files 111
- A.6 SETUP MENU 112
- Setup Menu 113
- A.6.1 Setup Input 114
- A.6.2 Setup Common Alarm 116
- A.6.3 Setup Sensor 117
- Setup Sensor (continued) 118
- A.6.4 Setup I/O Matrix 119
- A.6.5 Setup Output 125
- Pager Setup 127
- Modem Setup 128
- A.6.7 Setup System Info 129
- Change Password 129
- Setup Site ID 130
- Connect Battery 131
- Setup Service Phone Number 132
- Factory Defaults 133
- Initiate Remote Alarm Test 134
- A.6.8 Connect Expansion Board 135
- A.6.9 Override Output 136
- Clear Active Alarms 138
- Clear the Alarm Log 138
- Clear the Event Log 139
- Clear the Trend Logs 139
- SL-31060_REV3_02-13 144
Related products and manuals for Power supply units Emerson Liebert Remote Monitoring Panel
(48 pages)
(106 pages)© 2020, manymanuals.com. All rights reserved. | 0.727 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals