Emerson Liebert Remote Monitoring Panel User Manual Page 10
- Page / 144
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
Introduction
Liebert
®
Universal Monitor
™
2
1.5 Outside Enclosure Overview
The enclosure for the Liebert Universal Monitor controller board comes in two sizes:
•The large enclosure is designed to accommodate the Transformer Module and future
components, in addition to the controller board.
•The small enclosure is built to hold the controller board only.
Both enclosures are 2-3/4" deep.
Both enclosures have a built-in liquid crystal display (LCD) and a key lock, as shown in the example
below. The enclosures are made of metal to accommodate secure conduit fittings and protect
components against environmental debris.
Figure 1 Small enclosure—external features
The enclosure must be secured to a wall, either flush-mounted or recessed in the wall, as described in
2.0 - Installation - Main Board. Knockouts and access slots on the top and bottom allow easy
connection of wires and cables (see 4.0 - Wiring and Connections - Main Board) with either
mounting type.
Figure 2 Large enclosure—internal features
UNIVERSAL MONITOR
05-SEP-02 14:04:13
V5.100.0
PRESS =STATUS/SETUP
ESCESC
Universal MonitorUniversal Monitor
LCD for configuration
and operation
Key lock
The enclosure
has knockouts
and access slots
on top and
bottom for
cables and wires.
BAR CODE
BAR CODE
LIEBERT
START
TB7:
V INPU
UT
T
24V
V INPU
UT
T
+
—
+
—
(TOP)
ON
(BOTTOM)
0: COMMS
MS
485
TB3:
RELAY
OUTPUTS
TB2:
CONTACT
INPUTS
ASS REV
(BOTTOM)
(TOP)
4
3
2
1
(BOTTOM)
8
7
6
5
(BOTTOM)
(TOP)
4
3
2
1
(BOTTOM)
8
7
6
5
J11: PHONE
PIN 3-TIP
PIN 4-RI"N"G
MODEM
TB5: COMMON ALARM
(TERMINAL BLOCKS ROTATED IN VIEW)
(BOTTOM)
BOTTOM
Q11
R26
R402
P11
+
LS1
NO
NO
NO
N
ALARM
SENS
TOP
ENABLE
AUDIBLE
(TOP)
NO C NC NO C NC
ALL CIRCUITS;
CLASS 2
TB9: ANALOG
GROUND
+ +
——
+
—
+
—
3-4 BOTTOM
1-2 TOP
Back of LCD
Transformer Module
Controller Board
Ground wire
for LCD
On/Off switch
for Transformer
Module
Knockouts and
access slots
(top and bottom)
Power
receptacle
- Universal Monitor 1
- TABLE OF CONTENTS 3
- 7.0 VIEW STATUS OPTIONS 4
- 10.0 SPECIFICATIONS 5
- 1.0 INTRODUCTION 9
- ALL CIRCUITS; 10
- ALL CIRCUITS: 11
- 1.7 Controller Board Overview 12
- POWER INPUT 14
- RELAY OUTPUTS 14
- 1.9 LED Indicators 15
- K4K3K2K1 K5 K6 K7 K8 16
- 1.11 Typical Sequence 17
- 2.0 INSTALLATION - MAIN BOARD 18
- Required tools 19
- 2.2.1 Mounting the Panel 19
- 2.3.1 Mounting the Panel 20
- Input Power Connections 22
- Packing Contents 24
- 3.2.1 Mounting the Panel 25
- 3.3.1 Mounting the Panel 26
- 4.1 Wiring Specifications 28
- (BOTTOM) 29
- 4.3 Connecting Analog Inputs 30
- TB10: COMMS 31
- 4.5 EIA422 Liebert SiteScan 32
- Web Connector 32
- 5.1 Wiring Specifications 33
- S4 S3 S2 S1 34
- EIA485 + (to UM-) 34
- EIA485 - (to UM+) 34
- POWER INPUT RELAY OUTPUTS 35
- 29 Liebert 37
- 6.0 OVERVIEW OF MENUS 38
- 6.1 Opening Screen Overview 39
- 6.2 Main Menu Overview 39
- 6.3 LCD Menu Overview 39
- 7.1 View Active Alarms 41
- 7.2 View Alarm Log 42
- 7.3 View Event Log 43
- 7.4 View Trend Log 44
- 7.5 View Input Status 45
- 7.6 View Output Status 46
- 7.7 View Pager Numbers 47
- 9.1 Login 51
- ↑↓=NEXT ↵=SELECT 52
- ↑↓=SELECT ↵=NEXT/END 52
- 9.2 Setup System - Overview 53
- 9.3.5 Set Up Delay Time 55
- 9.5.3 Change Units Label 58
- 9.5.4 Change 4 mA Value 59
- 9.5.5 Change 20 mA Value 59
- 9.5.6 Change Offset Value 59
- 9.5.9 Change Low Setpoint 61
- 9.5.10 Change High Setpoint 61
- 9.5.11 Set Up Delay Time 62
- Supported Modem Settings 68
- Default Modem Settings 68
- Configuring the Modem 68
- 9.9.1 Change Password 77
- Change the Password 77
- 9.9.3 Setup Site ID 78
- 9.9.4 Connect Battery 78
- 9.9.8 Factory Defaults 84
- 9.11 Manual Output Ctrl 88
- 9.12 Clear Alarms & Logs 89
- 9.12.3 Clear the Event Log 90
- 9.12.4 Clear the Trend Logs 90
- 85 Liebert 93
- A.2.1 Connection Methods 94
- A.2.2 Create a Connection 95
- COM1 Port Setup 96
- Properties Setup 97
- ASCII Setup 97
- A.3 OVERVIEW OF MENUS 99
- A.4 VIEW STATUS MENUS 100
- A.4.1 View Active Alarms 101
- A.4.2 View Alarm Log 102
- A.4.3 View Event Log 103
- A.4.4 View Trend Log 104
- A.4.5 View Input Status 105
- A.4.6 View Output Status 106
- A.4.7 View Pager Numbers 107
- Main Menu 108
- Back Up Alarm Log File 109
- Back Up Event Log File 110
- Back Up Trend Log Files 111
- A.6 SETUP MENU 112
- Setup Menu 113
- A.6.1 Setup Input 114
- A.6.2 Setup Common Alarm 116
- A.6.3 Setup Sensor 117
- Setup Sensor (continued) 118
- A.6.4 Setup I/O Matrix 119
- A.6.5 Setup Output 125
- Pager Setup 127
- Modem Setup 128
- A.6.7 Setup System Info 129
- Change Password 129
- Setup Site ID 130
- Connect Battery 131
- Setup Service Phone Number 132
- Factory Defaults 133
- Initiate Remote Alarm Test 134
- A.6.8 Connect Expansion Board 135
- A.6.9 Override Output 136
- Clear Active Alarms 138
- Clear the Alarm Log 138
- Clear the Event Log 139
- Clear the Trend Logs 139
- SL-31060_REV3_02-13 144
Related products and manuals for Power supply units Emerson Liebert Remote Monitoring Panel
(48 pages)
(106 pages)© 2020, manymanuals.com. All rights reserved. | 0.825 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals