Emerson 3051S Specifications Page 35
- Page / 222
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
25
Reference Manual
00809-0100-4001, Rev JA
Section 2: Installation
November 2012
Installation
Perform the following procedure to make wiring connections:
1. Remove the housing cover on terminal compartment side. Do not remove the cover in
explosive atmospheres when the circuit is live. Signal wiring supplies all power to the
transmitter.
2. a. For 4-20 mA HART output, connect the positive lead to the terminal marked (+) and
the negative lead to the terminal marked (pwr/comm -). Do not connect powered
signal wiring to the test terminals. Power could damage the test diode.
b. For 1-5 Vdc HART Low Power output, connect the positive lead to the terminal
marked (+ pwr) and the negative lead to the terminal marked (pwr -). Connect signal
lead to V
out
/ comm +.
3. Plug and seal unused conduit connection on the transmitter housing to avoid moisture
accumulation in the terminal side. Install wiring with a drip loop. Arrange the drip loop
so the bottom is lower than the conduit connections and the transmitter housing.
Power supply for 4-20 mA HART
Transmitter operates on 10.5 - 42.4 Vdc. The dc power supply should provide power with less
than two percent ripple.
Note
A minimum loop resistance of 250 ohms is required to communicate with a Field
Communicator. If a single power supply is used to power more than one 3051 transmitter, the
power supply used, and circuitry common to the transmitters, should not have more than
20 ohms of impedance at 1200 Hz.
Figure 2-18. Load limitation
The total resistance load is the sum of the resistance of the signal leads and the load resistance
of the controller, indicator, and related pieces. Note that the resistance of intrinsic safety
barriers, if used, must be included.
Maximum Loop Resistance = 43.5 * (Power Supply Voltage – 10.5)
The Field Communicator requires a minimum loop resistance of 250
for communication.
See “Safety messages” on page 5 for complete warning
Voltage (Vdc)
Load (Ohms)
Operating
Region
1387
1000
500
0
10.5 20 30
42.4
- Protocol 1
- Rosemount 3051 Pressure 3
- Transmitter 3
- Title Page 4
- Contents 5
- 3Section 3: Configuration 6
- 5Section 5: Troubleshooting 7
- Reference Manual 10
- Table of Contents 10
- Section 1 Introduction 11
- 1.3 Models covered 12
- 1.4 Transmitter overview 13
- Section 2 Installation 15
- 2.3 General considerations 16
- 2.4 Mechanical considerations 17
- 2.8 Installation procedures 20
- Flange bolts 21
- Bolt installation 23
- 2.8.2 Impulse piping 24
- Mounting requirements 25
- 2.8.3 Process connections 26
- O-rings: 27
- 2.8.5 Housing rotation 28
- 2.8.6 LCD display 29
- Security (write protect) 30
- TRANSMITTER SECURITY 31
- JUMPER POSITIONS 31
- 2.9 Electrical considerations 32
- 2.9.2 Wiring 33
- Section 2: Installation 34
- Installation 34
- Power supply for 4-20 mA HART 35
- 2.9.4 Grounding 37
- Signal wiring 38
- Transmitter case 38
- External Ground 39
- Assembly 39
- Figure 2-24. Manifolds 40
- 2.11.4 Manifold operation 41
- 2.12 Liquid level measurement 44
- 2.12.1 Open vessels 45
- 2.12.2 Closed vessels 45
- Dry leg condition 46
- Wet leg condition 46
- Bubbler system in open vessel 46
- Figure 2-26. Wet leg example 47
- Section 3 Configuration 49
- 3.3 Commissioning 50
- 3.3.2 Wiring diagrams 51
- 3.5 Field communicator 52
- Section 3: Configuration 54
- Configuration 54
- 3.8 Check output 60
- 3.8.1 Process variables 61
- 3.8.2 Sensor temperature 61
- 3.9 Basic setup 62
- 3.9.3 Rerange 63
- Field communicator 65
- AMS device manager 65
- 3.9.4 Damping 67
- 3.10 LCD display 68
- 3.11 Detailed setup 71
- 3.12 Diagnostics and service 72
- 3.13 Advanced functions 74
- 3.13.2 Burst mode 77
- 3.14 Multidrop communication 78
- 4.1 Overview 81
- 4.2 Safety messages 81
- 4.3 Calibration overview 82
- TPE = = 0.117% of span 85
- TPE = = 0.105% of span 86
- 4.4 Analog output trim 87
- AMS Device Manager 89
- 4.5 Sensor trim 91
- 4.5.2 Zero trim 92
- 4.5.3 Sensor trim 93
- Zero effect 95
- Span effect 95
- Operation and maintenance 98
- Section 5 Troubleshooting 99
- 5.2.1 Warnings ( ) 100
- Section 5: Troubleshooting 101
- Troubleshooting 101
- Symptom Corrective actions 101
- 5.3 Diagnostic messages 102
- Operation 103
- Span Fail 104
- Local Dsbld 104
- Write Protect 104
- Message Description 105
- 5.4 Disassembly procedures 107
- 5.4.1 Remove from service 108
- 5.4.2 Remove terminal block 109
- 5.5 Reassembly procedures 110
- 00809-0100-4001, Rev JA 111
- November 2012 111
- A.1.2 Reference accuracy 114
- A.1.3 Total performance 114
- A.1.4 Long term stability 115
- A.1.5 Dynamic performance 115
- A.1.9 Vibration effect 116
- A.1.10 Power supply effect 117
- A.2 Functional specifications 118
- A.2.3 Service 120
- A.2.4 4–20 mA (Output Code A) 120
- fieldbus Parameters 121
- Minimum Load Impedance 123
- Indication 123
- Overpressure Limits 123
- A.2.13 Static Pressure Limit 124
- A.2.14 Burst Pressure Limits 124
- A.2.15 Failure Mode Alarm 124
- A.2.16 Temperature Limits 125
- A.3 Physical specifications 126
- A.3.3 Process-Wetted Parts 127
- A.3.5 Non-Wetted Parts 128
- A.3.6 Shipping Weights 129
- A.4 Dimensional Drawings 130
- 3051C Coplanar Flange 131
- Appendix A: Reference Data 132
- 3051T Dimensional Drawings 135
- Pipe Mounting Panel Mounting 136
- 3051L Dimensional Drawings 137
- A.5 Ordering Information 141
- (3051C with Option Code S1)) 146
- OUNDATION fieldbus Protocol ★ 149
- Axxxx Specials •• •• 165
- A.6 Options 166
- Shipping weights 169
- A.7 Spare parts 174
- OUNDATION or PROFIBUS PA) 177
- Mounting brackets Part number 182
- B.1 Overview 185
- B.2 Safety messages 185
- B.2.1 Warnings 186
- FM Approvals 187
- CSA international 187
- European certifications 188
- Japanese certifications 189
- IECEx certifications 189
- Inmetro certifications 190
- China certifications 191
- B.6 Approval drawings 194
- Product certifications 195
- Index-207 217
- Index-208 218
- Index-209 219
- Index-210 220
Related products and manuals for Measuring, testing & control Emerson 3051S
Philips GC3820 manuals
Owner’s manuals and user’s guides for DVD players Philips GC3820.
We providing pdf manuals Philips GC3820 for download free by document types:
More products and manuals for DVD players Philips
| Models | Document Type |
|---|---|
| MX5800SA/21 |
User Manual
Philips MX5800SA/21 User's Manual,
49 pages
|
| PET941D/98 |
User Manual
Philips PET941D/98 User's Manual,
2 pages
|
| DVD616K |
User Manual
Philips DVD616K User's Manual,
26 pages
|
| PET721D/98 |
User Manual
Philips PET721D/98 User's Manual,
2 pages
|
| DVP3258X/94 |
User Manual
Philips DVP3268/94 User manual,
52 pages
|
| PET741V/37 |
User Manual
Philips PET741R/37 User manual,
19 pages
|
| HTS6515D/37 |
User Manual
Philips HTS6515D/37 User manual,
52 pages
|
| HTS3500K |
User Manual
Philips HTS3500K User's Manual,
49 pages
|
| DVP 5986K |
User Manual
Philips DVP5986K/96 User manual,
2 pages
|
| DVP3120/12 |
User Manual
Philips DVP3120/12 User manual,
39 pages
|
| DVP2320BL |
User Manual
Philips DVP2320BL User's Manual,
20 pages
|
| PET721D/79 |
User Manual
Philips PET721D/79 User manual,
21 pages
|
| HTS3300/55 |
User Manual
 
Philips HTS3300/55 Manual de usuario,
4 pages
|
| FWD790/21M |
User Manual
Philips FWD790/21M User manual,
2 pages
|
| DVD 765K |
User Manual
Philips DVD 765K User's Manual,
26 pages
|
| DVD 620/001 |
User Manual
Philips DVD 620/001 User's Manual,
24 pages
|
| DVP5960/37 |
User Manual
Philips DVP5960/37 User manual,
2 pages
|
| DVP5140 |
User Manual
Philips DVP5140 User's Manual,
47 pages
|
| DVD763SA/021 |
User Manual
Philips DVD763SA/021 User's Manual,
64 pages
|
| DVP5992 |
User Manual
Philips DVP5992 User's Manual,
2 pages
|
© 2020, manymanuals.com. All rights reserved. | 0.038 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals