Emerson 644 Specifications Page 79
- Page / 182
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
69
Reference Manual
00809-0200-4728, Rev RA
Section 5: Operation and Maintenance
April 2015
Operation and Maintenance
5.3.1 Trimming
The trim functions should not be confused with the rerange functions. Although the rerange
command matches a sensor input to a 4–20 mA output—as in conventional calibration—it does
not affect the transmitter’s interpretation of the input.
One or more of the trim functions may be used when calibrating. The trim functions are as
follows:
Sensor Input Trim
Transmitter-Sensor Matching
Output Trim
Output Scaled Trim
5.4 Sensor input trim
The sensor trim command allows for alteration of the transmitter’s interpretation of the input
signal. The sensor trim command trims, in engineering (°F, °C, °R, K) or raw (ohms, mV) units,
the combined sensor and transmitter system to a site standard using a known temperature
source. Sensor trim is suitable for validation procedures or for applications that require profiling
the sensor and transmitter together.
Perform a sensor trim if the transmitter’s digital value for the primary variable does not match
the plant’s standard calibration equipment. The sensor trim function calibrates the sensor to
the transmitter in temperature units or raw units. Unless the site-standard input source is
NIST-traceable, the trim functions will not maintain the NIST-traceability of your system.
Figure 5-1. Trim
Application: Linear Offset Application: Linear Offset and
Slope Correction
Solution: Single-Point Trim Solution: Two-Point Trim
Method:
1. Connect sensor to transmitter. Place
sensor in bath between range points.
2. Enter known bath temperature using the
Field Communicator.
Method:
1. Connect sensor to transmitter. Place
sensor in bath at low range point.
2. Enter known bath temperature using
the Field Communicator.
3. Repeat at high range point.
One-Point Trim Two-Point Trim
Transmitter System Curve
Site-Standard Curve
Resistance (ohms)
Temperature
Resistance (ohms)
Temperature
- Protocol 1
- Rosemount 644 3
- Temperature Transmitter 3
- Title Page 4
- Contents 5
- 6Section 6: Troubleshooting 8
- Reference Manual 10
- Table of Contents 10
- Section 1 Introduction 11
- 1.2 Overview 12
- 1.2.2 Transmitter overview 13
- 1.3 Considerations 14
- 1.4 Return of materials 15
- 1.5 Transmitter security 16
- Section 2 Configuration 17
- 2.3 System readiness 18
- 2.4 Configuration methods 19
- Configuring with an LOI 21
- 2.4.4 Failure mode 22
- 2.5 Verify configuration 23
- 2, 2, 8, 6 26
- 2.6.3 Setting output units 28
- Setting output units with LOI 29
- Communicator 30
- 2, 2, 3, 3 31
- Resetting Hot Backup 33
- 2.8 Configure device outputs 35
- 2.8.2 Damping 36
- 2, 2, 1, 5 2, 2, 1, 6 38
- Configuring tag with LOI 43
- 2.10.1 50/60 Hz filter 44
- 2.10.2 Resetting the device 44
- 2.11 Diagnostics and service 46
- 2, 2, 4, 3, 4 48
- AMS terms 49
- Configure min/max with LOI 50
- Special considerations 53
- Hot Backup 53
- 3.1 Overview 55
- 3.2 Safety messages 55
- 3.3 Considerations 56
- 3.4 Installation procedures 57
- 3.4.1 Set the alarm switch 58
- 3.4.2 Mount the transmitter 59
- 3.4.3 Install the device 60
- 4.1 Overview 67
- 4.2 Safety messages 67
- 4.3.1 Sensor connections 69
- 4.3.2 Power the transmitter 70
- 4.3.3 Ground the transmitter 71
- Shielding recommendations 72
- Option 2 73
- Option 3 73
- Grounded thermocouple inputs 74
- (HART/4–20 75
- Electrical Installation 76
- Figure 4-4. Load Limits 76
- 5.1 Overview 77
- 5.2 Safety messages 77
- 5.3 Calibration overview 78
- 5.4 Sensor input trim 79
- 3, 4, 4, 1 80
- 3, 4, 4, 2 81
- 5.5 Trim the analog output 82
- 3, 4, 5, 1 83
- 3, 4, 5, 2 83
- 5.7 Switching HART Revision 86
- Section 6 Troubleshooting 87
- 6.4 Diagnostic messages 90
- (SIS) Certification 93
- 7.4 Commissioning 94
- 7.5 Configuration 95
- 7.7.1 Proof test 96
- 7.7.2 Partial proof test 96
- 7.8 Specifications 98
- 7.8.3 Product life 99
- A.1 Specifications 101
- A.1.2 Physical 102
- OUNDATION 103
- A.1.3 Performance 104
- Sensor connections 105
- Communication requirements 106
- Power supply 107
- Temperature limits 107
- Turn-on time 108
- External transient protection 108
- Accuracy 108
- Accuracy example 110
- OUNDATION fieldbus 111
- 644H (DIN A Head Mount) 113
- 644 Field Mount 114
- 644 Rail Mount 114
- Sanitary Applications 117
- A.4 Ordering information 118
- 00809-0200-4728, Rev RA 123
- April 2015 123
- 2 NPT 00644-4438-0002 126
- 2 NPT 00644-4438-0102 126
- 2 NPT 00644-4438-0004 126
- 2 NPT 00644-4438-0104 126
- A.4.1 Configuration 127
- A.4.2 Tagging 127
- A.4.3 Considerations 127
- Custom configuration 128
- Head Mount 129
- A.5.2 Physical specifications 130
- Enclosure ratings (644H) 131
- Sanitary housing surface 131
- Load limitations 133
- Configuration 135
- ≤ Ta ≤ +85°C); Type 4X; 137
- 2-14 NPT) enclosure 137
- International 140
- Gas -40 °C ≤ Ta ≤ +65 °C 142
- Dust -40 °C ≤ Ta ≤ +85 °C 142
- T5 -40 °C ≤ Ta ≤ +70 °C 145
- T6 -60 °C ≤ Ta ≤ +40 °C 145
- T5 -60 °C ≤ Ta ≤ +85 °C 145
- Combinations 146
- Additional Certifications 147
- Product Certifications 149
- Sheet 2 of 2 158
- Trees and Fast Keys 165
- D.1 Number entry 173
- D.2 Text entry 174
- 175
- Canceling 176
- D.5 LOI menu tree 177
Related products and manuals for Measuring, testing & control Emerson 644
(92 pages)© 2020, manymanuals.com. All rights reserved. | 1.423 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals