Emerson E2 User Manual Page 24
- Page / 273
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
1-8 • E2 RX/BX/CX I&O Manual 026-1610 Rev 13 14-SEP-2011
To use on-line help from any screen in the E2 front
panel interface, simply press the E2’s permanent Help
key. This opens a pop-up window containing either
information about the screen or menu you are currently on,
or information about the input, output, or setpoint you
have highlighted with the cursor (if available). After the
Help
key has been pressed, will open the Gen-
eral Help menu containing Troubleshooting options.
1.7 Software Licensing
Some applications in the E2 are available only when
activated with a unique license key that is obtained
through Retail Solutions. Software licensing (see Section
10.15, License Management) allows the user to activate
certain features in the E2, such as Web Services and third-
party controllers. Call your Retail Solutions sales repre-
sentative at 770-425-2724 for more information about
software licensing.
- 026-1610 Rev 13 14-SEP-2011 1
- Table of Contents 5
- 1Introduction 17
- 1.2 The E2 Building Con 18
- 1.3 The E2 Convenience 19
- Store Controller 19
- 1.4 Networking Overview 20
- E2 RX & BX 21
- ECHELON NETWORKS 21
- 1.5 Documentation Over 22
- 1.6 On-Line Help System 23
- Overview 23
- 1.7 Software Licensing 24
- 2 Hardware Overview 25
- - E2 PIB 26
- - E2 Keyboard 26
- - PIB LED’s Status 26
- 2.2 I/O Network Boards 27
- 2.2.2 MultiFlex Boards 28
- Output Boards 29
- 2.2.2.3 MultiFlex CUB 31
- (RCB) (BX and CX Only) 31
- 2.2.2.6 MultiFlex PAK Board 31
- 2.2.3 The MultiFlex ESR Board 32
- 814-3110) 32
- - 8RO Relay Output Board 33
- - 8ROSMT Relay Output Board 33
- 2.2.6 4AO Analog Output Board 34
- 2.3 Echelon Network 35
- Boards and Peripherals 35
- 2.3.5 The ESR8 (Discontinued) 36
- 2.3.6 TD3 Temperature Display 37
- 3 Mounting 39
- 3.1.3 Retrofit Mounting 40
- 3.2 Mounting I/O Boards 41
- (Snap Track) 42
- 3.3.1 16AIe and 8ROe 42
- 3.3.3 ESR8 (Discontinued) 43
- 3.3.4 MultiFlex ESR 43
- 3.3.5 TD3 43
- 3.4.2 Two-Channel and Four 44
- Channel Repeaters 44
- 3.5.1 Pressure Transducers 45
- 3.5.2.2 Mounting 46
- 3.5.3.1 Location 46
- 3.5.3.2 Mounting 46
- 3.5.4.1 Location 46
- 3.5.4.2 Mounting 46
- 3.5.6.1 Location 47
- 3.5.8.1 Indoor RH Sensor 47
- 3.5.8.2 Outdoor RH Sensors 48
- 3.5.9 Dewpoint Probe 49
- 3.5.10 Light Level Sensor 49
- 3.5.11 Liquid Level Sensors 49
- 4 E2 Hardware Setup 51
- 4.2 Powering the E2 52
- 4.3 Add-On E2 Peripherals 53
- 4.4 Battery Testing and 55
- Replacement 55
- --- to 56
- for Yes and press 56
- for Yes, then press 56
- RS485 I/O or MODBUS Net 57
- 5 Serial Configura 59
- E2 PIB COM PORT ASSOCIATIONS 60
- 6.1 The I/O Network 61
- 6.1.2.1 Board Designation 62
- 6.1.2.2 Board Calculations 62
- X + (Y • 8) < 256 62
- Numbers) 63
- 6.1.7 Setting the Baud Rate 63
- Biasing Jumpers 64
- 6.1.9 Powering the I/O Boards 64
- 6.2 IMC/Prodigy Rooftop 65
- Unit Controllers 65
- 6.3 ECT MODBUS 66
- 6.3.4 iPro DAC 67
- 6.3.5 Energy Meter 67
- Detection Sensor (MRLDS) 67
- Sense Protection 68
- System (RLDS) 71
- 6.3.11.1 XM670 72
- 6.3.11.2 XM679 72
- 6.3.11.3 XM678 72
- 4-20 OUT 75
- 120/208/240 VAC 77
- 16AI INSTALLATION GUIDE 78
- RS485 I/O NET 79
- XEV22D DRIVER TO E2 80
- INSTALLATION GUIDE 80
- XR35CX, XR75CX TO E2 81
- 7.1 Ethernet IP Configura 83
- 7.2 Hardware Specifica 83
- 7.3 Software Specifica 84
- 7.4 Ethernet Network 84
- 7.5 Software Setup 85
- 7.6 Troubleshooting 86
- 8.1 Overview 87
- 8.2 Wiring Type 87
- 8.3 Echelon Network 87
- Structuring (Daisy-Chains) 87
- 8.4 Device Termination 88
- 8.5 Wire Restrictions 89
- 8.6 Installing Echelon 89
- 8.7 LEDs 90
- 8.8 Open Echelon Device 90
- Connectivity 90
- (Network Setup) 91
- 8.8.1.1 Troubleshooting 91
- Valve #4 93
- 9 Input and Output Setup 95
- 9.1.2 Power Connection 96
- (System Configuration) 100
- (Input Definitions) 100
- - Data Type Pop-Up Menu 101
- (potentiometer) 102
- - Digital Input Screen 103
- 9.2 The 8RO, 8ROe, 8IO 104
- (Output Definitions) 105
- - Digital Output Screen 106
- - Analog Output Screen 107
- 9.3 CC-100 Case Control 108
- 9.3.2 Power Module Wiring 109
- 9.3.3 Valve Cable 109
- 9.4 ESR8 Valve Output 110
- TOP OF BOARD 111
- 10 Quick Start 113
- 10.3 Setting Number of 114
- Network Devices 114
- 10.4 Setting Number of 115
- Applications 115
- 10.5 The Main Status 115
- (Home) Screen 115
- 10.6 Common Screen Ele 116
- 10.7 Screen Types 117
- (Setup). The actual setup 118
- (System Information) 120
- 10.8 Time/Date Setup 121
- 10.9 Set Up Modem 122
- 10.10 Set Up TCP/IP 123
- 10.11 Set Up Network Baud 124
- 10.12 Set Up User Access 125
- if you are 126
- 10.13 Set Up I/O Network 127
- 10.14 Set Up Echelon Net 128
- (Network Setup) 129
- (Network Summary) 129
- (DISCONTINUED) 130
- 10.15 License Management 131
- (Licensing) 132
- 10.16 Set Up Alarming 133
- (General Controller Info) 134
- (Alarm Setup) 135
- (Dial-out Setup) 135
- 10.17 Set Up Global Data 136
- 10.18 Set Up Applications 137
- to add an application 138
- (Delete Application) 138
- to open the Actions 139
- and 140
- Property Help 141
- 11 Software Overview 143
- 11.1.4 Hardware Overview 144
- 11.2 Condenser Control 145
- 11.2.2 Evaporative Condensers 146
- 11.2.3 Fan Control 146
- 11.2.4 Condenser Split Mode 146
- 11.2.5 Fast Recovery 146
- 11.2.6 Hardware Overview 146
- 11.3 Standard Circuits 147
- 11.3.2 Defrost Control 148
- 11.4 Case Control Circuits 152
- 11.4.3 Refrigeration Control 153
- 11.4.4 Defrost Control 154
- 11.4.5 Anti-Sweat Control 155
- 11.4.6 Dual Temp Control 156
- 11.4.7 Fan Control 156
- 11.4.8 Light Control 156
- 11.4.9 Clean/Wash Mode 156
- 11.4.11 Fail-Safe Mode 157
- 11.5 Logging Groups 158
- 11.5.1 Possible Data Errors 159
- 11.5.2 Data Compression 159
- 11.5.3 Base Log Group 159
- System Configuration 160
- Logging Setup 160
- 11.5.5 Logging Group Status 161
- 11.5.6 Log Reports 161
- for System Configuration 162
- Display Logged Points 162
- 11.6 Air Handling Units 163
- 11.6.5 Economizer Control 164
- 11.6.9 Curtailment 165
- 11.6.11 Separate Setpoints 166
- 11.6.12 AHU Zone Control 166
- 11.6.13 Hardware Overview 166
- 11.7 Zone Control 167
- 11.7.2 How Zones Work 168
- Connected To Zones 168
- 11.7.4 Temperature Control 169
- 11.7.5 Zone Temperature 169
- 11.7.6 Economizer Control 169
- 11.7.7 Economization Enable 169
- 11.7.11.2 AHUs 170
- the Network Setup menu 171
- for Associations 171
- 11.8 MultiFlex CUB Board 172
- 11.9 MultiFlex PAK Board 172
- 11.10 Lighting Schedules 172
- 11.10.3 Control Method Select 173
- 11.10.4 Standard Control 173
- 11.10.5 Alternate Control 174
- 11.10.7 The Min ON/OFF Cell 175
- 11.10.8 The Proof Cell 175
- 11.11 Demand Control 176
- 11.11.3 Load Shedding 177
- 11.11.4 Shedding Levels 177
- 11.11.5 Priority Levels 177
- - Shedding Priority Levels 178
- Load Shedding 179
- 11.12 Sensor Control 180
- 11.13 Loop/Sequence Con 181
- Descriptions 182
- 11.14 Time Scheduling and 184
- Holidays 184
- 11.15 Power Monitoring 185
- 11.15.2 Logging 186
- 11.16 Anti-Sweat Setup 187
- 11.17 Heat/Cool Control 187
- 11.17.4 Setpoint Reset 188
- 11.18 Analog and Digital 189
- Combiners 189
- 11.19 TD Control 190
- 11.20 Pulse Accumulation 191
- 11.21 Irrigation Control 192
- 11.21.3 Cycle Scheduling 193
- 11.21.4 Zone Inhibit 193
- 11.21.5 Zone Bypass Inputs 193
- 11.21.5.1 Bypass Failsafe 194
- 11.21.6.1 Leak Test 194
- 11.22 Flexible Combiner 195
- 11.23 Modular Chiller Con 195
- 11.23.2 Learning Mode 196
- 11.23.4 Compressor Control 196
- 11.24 Boiler 197
- 11.25 Refrigerant Monitor 198
- 11.26 Detailed Setpoint 198
- Change Logging 198
- 11.26.2 Logged Changes 199
- 11.26.3 Unlogged Changes 199
- 12.1 The E2 Home Screen 201
- 12.2 Logging On and 202
- Access Levels 202
- 12.3 Toggling Full Options 203
- 12.4 Navigation 203
- 12.4.2 Screen Types 205
- . This will take you to 205
- 12.4.3 The E2 Keypad 206
- key moves the 207
- key together 208
- 12.5 Customizing the 209
- Home Screen 209
- 12.6 Manual Defrost and 209
- Clean Mode 209
- 12.7 Overrides 210
- 12.8 Checking Boards 211
- 12.9 Checking Status 211
- 12.10 Alarms 212
- 12.10.8.1 Acknowledging 213
- 12.10.8.2 Resetting 214
- 12.10.8.3 Clearing 214
- 12.11 Viewing Logs and 215
- 12.11.2 Log View 217
- to open the Actions Menu 217
- 12.11.3 The Graph View 217
- 12.11.4 Zooming In and Out 217
- 12.12 Low Battery Notifica 218
- 12.13 Naming Conventions 218
- Alarm Name 224
- Default 224
- Priority 224
- Definition 224
- P Proportional Mode 237
- I Integral Mode 237
- D Derivative Mode 237
- Integral Mode 238
- “P” + “I” MODES 239
- How Condenser Control and 240
- HVAC PID Differs From The 240
- Other PID Features 241
- Minimum Accumulated Error 242
- Filtering 242
- Limits and Precision Tab 245
- Appendix F: Troubleshooting 249
- . Highlight the Point 256
- Appendix G: Revision Log 259
Related products and manuals for Thermostats Emerson E2
Thermostats Emerson EE542-1Z User Manual
(24 pages)
(24 pages)
Thermostats Emerson 1F95EZ-0671 Setup Guide
(24 pages)
(24 pages)
Thermostats Emerson 99 User Manual
(16 pages)
(16 pages)
Thermostats Emerson E2 Einstein Specifications
(263 pages)
(263 pages)
Thermostats Emerson 99 Instruction Manual
(24 pages)
(24 pages)
Thermostats Emerson EE542-1Z User Manual
(28 pages)
(28 pages)
Thermostats Emerson 1F98EZ-1421 User's Guide
(20 pages)
(20 pages)
Thermostats Emerson 250-5000 Specifications
(32 pages)
(32 pages)
© 2020, manymanuals.com. All rights reserved. | 3.101 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals