Emerson FXMP25 User's Guide Page 72
- Page / 116
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
72 Mentor MP Short Form Guide
www.leroy-somer.com Issue : c
6.2 Quick start commissioning / start-up (from USA defaults)
Action Detail
Before
power-up
Ensure:
• Drive Enable signal is not given (terminal 31)
• Run signal is not given
• Motor connected
• Tacho connected if one is being used
• Encoder connected if one is being used
Power-up
the drive
Ensure:
• Drive displays ‘inh’
Motor thermistor input is disabled by default. If motor thermistor is available
the thermistor should be used. The protection is enabled with Pr 7.15 (in01,
0.81).
For drive trips, see Chapter 9 Diagnostics on page 107.
Enter motor
nameplate
details
Enter:
• Armature rated voltage in Pr 5.09 (SE06, 0.27) (V)
• Motor rated current in Pr 5.07 (SE07, 0.28) (A)
• Motor rated speed (base speed) in Pr 5.08 (SE08, 0.29) (rpm)
• Field rated voltage in Pr 5.73 (SE11, 0.32) (V)
Set motor
feedback
parameters
Incremental encoder basic set-up
Enter:
• Drive encoder type in Pr 3.38 (Fb07, 0.77) = Ab (0): Quadrature encoder
• Encoder power supply in
Pr 3.36 (Fb06, 0.76)
= 5V (0), 8V (1), 15V (2) or
24V (3)
If output voltage from the encoder is >5V, then the termination resistors
must be disabled
Pr 3.39 (Fb08, 0.78)
to 0.
• Drive encoder lines per revolution (LPR) in Pr 3.34 (Fb05, 0.75) (set
according to encoder)
• Drive encoder termination resistor setting in Pr 3.39 (Fb08, 0.78)
0 = A-A\, B-B\, Z-Z\ termination resistors disabled
1 = A-A\, B-B\, termination resistors enabled, Z-Z\ termination
resistors disabled
2 = A-A\, B-B\, Z-Z\ termination resistors enabled
Tachometer set-up
Enter:
• Tachometer voltage rating Pr 3.51 (Fb02, 0.72) (V/1000 rpm)
• Tachometer input mode Pr 3.53 (Fb03, 0.73)
Set
maximum
speed
Enter:
• Maximum speed in Pr 1.06 (SE02, 0.23) (rpm)
For field weakening the field controller needs to be setup in current control by
setting Pr 5.75 = OFF, setting the rated field current into 5.70 (SE10, 0.31)
and setting Pr 5.64 to On.
For field weakening in Estimated Speed Mode please refer to the Mentor MP
User Guide - Chapter 8 Optimization - Field current.
NOTE
Mot X XXXXXXXXX
No XXXXXXXXXX kg
XXXXXXXXXXXXXXXXXXXXXXXXXX
X
X
XX
XX
XXX
XXX
XX
XX
XXX
XXX
X
X
XXXXXXXXXX XXXXXXXXXXXXXXXX XXXXXXXXX
XXXXXXXXXXXXXXXXXXXXXXXXXX
XXXXXXXXXXXXXXXXXXXXXXXXXX
XXXXXXXXXXXXXXXXXXXXXXXXXX
Setting the encoder voltage supply too high for the encoder
could result in damage to the feedback device.
CAUTION
NOTE
NOTE
SE02
t
- MENTOR MP 1
- Contents 3
- 4 Mentor MP Short Form Guide 4
- Mentor MP Short Form Guide 5 5
- 1 Safety Information 6
- 1.10.1 Electric shock risk 8
- 1.10.2 Stored charge 8
- 2 Product information 9
- 10 Mentor MP Short Form Guide 10
- MP 2 0 01 4 R 11
- 12 Mentor MP Short Form Guide 12
- STORED CH ARG E 13
- Mode /Reset 13
- 14 Mentor MP Short Form Guide 14
- Mentor MP Short Form Guide 15 15
- STORED CHARGE 16
- Risk of Electric Shock 17
- Power down unit 10minutes 17
- 3 Mechanical installation 18
- Pozi Pz2 19
- 3.3 Mounting method 20
- Mentor MP Short Form Guide 23 23
- 7.6mm (0.30 in) 23
- (1.97in) 25
- 202mm (7.95in) 26
- L1 L2 L3 29
- Enclosure layout 30
- 4 Electrical installation 31
- 32 Mentor MP Short Form Guide 32
- 4.2 Ground connection 33
- 34 Mentor MP Short Form Guide 34
- 4.4 Line reactors 35
- 36 Mentor MP Short Form Guide 36
- 4.5 Control 24Vdc supply 37
- 38 Mentor MP Short Form Guide 38
- 40 Mentor MP Short Form Guide 40
- 4.6.1 Ferraz Shawmut fuses 41
- 42 Mentor MP Short Form Guide 42
- Mentor MP Short Form Guide 43 43
- 44 Mentor MP Short Form Guide 44
- 46 Mentor MP Short Form Guide 46
- 4.6.2 Alternative fusing 47
- 4.6.3 Internal field fuses 48
- 4.7.1 Motor cables 48
- 4.7.2 Encoder cable 48
- 4.7.3 Control cables 49
- 50 Mentor MP Short Form Guide 50
- Mentor MP Short Form Guide 51 51
- 52 Mentor MP Short Form Guide 52
- 5 Getting started 53
- 54 Mentor MP Short Form Guide 54
- 5.3 Menu 0 (sub block) 55
- 56 Mentor MP Short Form Guide 56
- 58 Mentor MP Short Form Guide 58
- 5.4 Pre-defined sub blocks 59
- Speed loop 60
- Serial interface 60
- Speed feedback 60
- 5.5 Menu 0 (linear) 61
- 62 Mentor MP Short Form Guide 62
- Mentor MP Short Form Guide 63 63
- Procedure 64
- 5.13.1 User security 66
- 5.13.2 Setting user security 67
- 6 Running the motor 68
- Mentor MP Short Form Guide 69 69
- 70 Mentor MP Short Form Guide 70
- Mentor MP Short Form Guide 71 71
- 72 Mentor MP Short Form Guide 72
- Mentor MP Short Form Guide 73 73
- 7 SMARTCARD operation 74
- 7.3 Transferring data 75
- 8 Advanced parameters 76
- Mentor MP Short Form Guide 77 77
- 78 Mentor MP Short Form Guide 78
- Mentor MP Short Form Guide 79 79
- Speed accuracy and resolution 80
- Mentor MP Short Form Guide 81 81
- 82 Mentor MP Short Form Guide 82
- Mentor MP Short Form Guide 83 83
- 84 Mentor MP Short Form Guide 84
- Mentor MP Short Form Guide 85 85
- 86 Mentor MP Short Form Guide 86
- Mentor MP Short Form Guide 87 87
- 88 Mentor MP Short Form Guide 88
- 8.7 Menu 7: Analog I/O 89
- 90 Mentor MP Short Form Guide 90
- 92 Mentor MP Short Form Guide 92
- 94 Mentor MP Short Form Guide 94
- Mentor MP Short Form Guide 95 95
- 96 Mentor MP Short Form Guide 96
- Mentor MP Short Form Guide 99 99
- Figure 8-17 Brake sequence 99
- Mentor MP Short Form Guide 100
- Issue : c www.leroy-somer.com 101
- 9 Diagnostics 107
- 9.2 Alarm indications 110
- 9.3 Status indications 111
- 9.4 Trip masking 111
- Motor overload protection 112
- Over speed protection 112
- 10.3 Safety label 113
- 10.4 UL Listed accessories 113
- 338 567 258 RCS ANGOULÊME 116
Related products and manuals for Recording Equipment Emerson FXMP25
(32 pages)© 2020, manymanuals.com. All rights reserved. | 2.832 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals