Emerson CF3300ORH Owner's Manual download pdf (Page 7)

6. Carefully lift the fan assembly and seat the

hangerball/downrod fan assembly into the hanger

bracket. Be sure the groove in the hanger ball lines

up with the tab on the hanger bracket

(Figure 9).

7. Install the end of the fan support cable through one

of the holes in the large brass bushing. Do not

allow the bushing to slide down the cable and into

the downrod (Figure 9A).

8. Install the end of the fan support cable through the

center of the small brass bushing (supplied). Now

pass the fan support cable through the loop

provided on the free end of the ceiling support

cable previously installed into the building

structure. Next, pass the fan support cable back

through the center of the small brass bushing in the

opposite direction as the first pass. Pull as much

cable as possible through the brass bushing

(Figure 9A).

CEILING

SUPPORT CABLE

HANGER

BRACKET

OUTLET BOX

CEILING JOIST

WOOD MEMBER

(2" x 4" Approx.)

Figure 8

ATTACH SUPPORT WIRE TO

CEILING SUPPORT WIRE

HANGER BALL/DOWNROD

ASSEMBLY

HANGER BALL TAB

Figure 9

1. Securely attach the ceiling support wire to the

ceiling joist or structural member using the 3/8 x 2”

hex lag bolt and flat washer. Drill a maximum

diameter 1/4” pilot hole into the supporting member

to prevent splitting or cracking. Install a washer

onto the screw and insert the screw through one of

the loops (Figure 8). Securely tighten the screw

into the structure.

IMPORTANT

Do not use any lubricant when installing the lag

bolts.

IMPORTANT

The pilot holes should be drilled no larger than

the minor diameter of the mounting screw

threads, and at least 1-1/2 inches of the threaded

part of the mounting screw should be inches

secured into a structural wood joist to provide

secure mounting.

2. Drill a second maximum diameter 1/4” pilot hole up

through the center of the electrical box (Figure 8).

Install the hanger bracket assembly using 3/8 x 5”

lag bolt and 3/8” flat washer. Route the electrical

supply wires through the opening provided on the

hanger bracket. Do not completely tighten the lag

bolt, leave it lose enough such that the hanger

bracket assembly can be freely rotated against the

electrical box.

3. Temporarily hang the ceiling fan assembly on the

hanger bracket, be sure the hanger ball groove

engages the hanger bracket tab. Rotate the fan

assembly and hanger bracket to the desired

orientation. Remove the fan assembly from the

hanger bracket.

4. Completely tighten the center lag bolt while holding

the hanger bracket in the desired position.

IMPORTANT

If you are installing your ceiling fan on a sloped

ceiling, the hanger bracket must be mounted with

the hanger ball opening facing up-slope.

Hanger bracket must seat firmly against outlet

box. If the outlet box is recessed, remove wall

board until bracket contacts box. If bracket

and/or outlet box are not securely attached, the

fan could wobble or fall.

WARNING

5. Position the motor lead wires and support cable on

the back side of the hanger bracket for final

connection to the electrical supply wires.

Failure to seat tab in groove could cause

damage to electrical wires and possible shock

or fire hazard.

WARNING

To avoid possible fire or shock, do not pinch

wires between the hanger ball/downrod

assembly and hanger bracket.

WARNING

U.L. Model No.: CF3300

NOTE: If not done so already, carefully remove

the masking tape applied to the motor leads and

support wire to complete wiring.

1 2 3 4 5 6 7 8 9 10 11 12 ... 15 16

Comments to this Manuals

No comments

Emerson CF3300ORH Owner's Manual Page 7

Comments to this Manuals

Related products and manuals for Household fans Emerson CF3300ORH