Emerson Liebert NX User Manual Page 42
- Page / 132
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
Options
32 Liebert
®
NX
™
5.2.3 Operating Principles
Redundancy Paralleling
The parallel redundant system can noticeably improve system reliability. In normal condition, none of
the UPS modules work at full load. That means that even if the load is increased, the system will not
transfer to bypass. And when a UPS module shuts down due to any failure, the remaining UPS
modules can still power and protect the load. When redundancy is lost due to module failure or load
increase, the parallel system will trigger an alarm.
5.2.4 Operation Modes Summary
The parallel system also has operation modes such as normal, battery, bypass and maintenance
bypass. All UPS modules in the parallel system operate in coordination.
• Normal Mode Operation
The load is powered by the inverters of all the UPS modules in the system. If the frequency of
bypass is within the synchronous range, the inverter will be synchronized with the bypass.
Otherwise, the system will operate at nominal frequency.
• Battery Mode Operation
The batteries of all UPS modules power the load through their inverters. The system operates at
nominal frequency.
• Bypass Mode Operation
The condition to transfer to bypass mode is essentially the same as that of single module system.
The bypass of all the UPS modules powers the load.
• Maintenance Bypass Mode Operation
The sequence to transfer to maintenance bypass mode is the same as for transferring a single-
module system. The maintenance bypass switches should be switched on as synchronously as
possible. Thus the system can be repaired without interrupting the power supply to critical load.
If ECO mode is selected, the double-conversion UPS operation is inhibited at most times for the
purpose of saving energy. In this mode of operation, not unlike UPS of line-interactive or standby
technology, the bypass is the preferred source. Only when the voltage and/or frequency of the
bypass supply is beyond pre-defined and adjustable limits is the critical AC load transferred to
the inverter.
5.3 Installing Parallel System
The basic installation procedure of parallel system is the same as that of single module system. The
following sections introduce only the installation procedures specific to the parallel system.
5.3.1 Conditions for Parallel System
• Each UPS module must have the same bypass source.
• The outputs of all UPS modules are connected altogether.
• The main inputs can be from different sources, but the phase rotation sequence of main inputs,
bypass inputs and outputs must be correct and the same.
• The parallel logic cable and load sharing cable must be connected in a ring correctly (see
Figure 17).
NOTICE
Risk of creating parallel systems with incorrect power ratings. Can cause equipment damage.
When paralleling UPS’s with different power ratings, the power rating of the larger UPS can
be no more than four times the power rating of the smaller UPS.
• 40-80kVA Liebert NX units can be installed in parallel with 80-120kVA Liebert NX units.
• 80-120kVA Liebert NX units can be installed in parallel with 160-200kVA.
• 40-80kVA Liebert NX units must not be installed in parallel with 160-200kVA Liebert NX
units.
- 2
- TABLE OF CONTENTS 3
- 7.0 LIEBERT BDC 4
- SAVE THESE INSTRUCTIONS 11
- 2Liebert 12
- Battery Cabinet Precautions 13
- 4Liebert 14
- GLOSSARY OF SYMBOLS 15
- 1.0 INTRODUCTION 16
- 2.0 INSTALLATION 17
- 2.3 Preliminary Checks 18
- 2.4 UPS Location 18
- Battery Location 19
- Final Position 19
- 2.6 Mechanical Considerations 20
- 2.6.4 Optional Cabinets 21
- Installation 22
- 12 Liebert 22
- 3.0 ELECTRICAL CONNECTIONS 23
- 3.1.2 UPS Input Configuration 24
- 3.1.3 Cabling Guidelines 24
- 3.1.4 Cable Connections 25
- 3.1.5 Safety Ground 25
- 3.1.6 Protective Devices 25
- 3.1.7 Cabling Procedure 26
- Common Input Connections 26
- Dual Input Connections 26
- Frequency Converter Mode 27
- 3.2 Control Cables 28
- 3.3 Dry Contacts 30
- 3.3.4 Output Dry Contacts 31
- EPO - NO 32
- EPO - NC 32
- 4.0 BATTERY INSTALLATION 33
- 4.3.1 Battery Cabinets 34
- 4.4 Non-Standard Batteries 36
- 4.5 BCB Shunt Trip 37
- 5.0 OPTIONS 38
- LBS Cable 39
- 5.2.1 General 40
- 480V, 3W 41
- System Input 41
- System Output 41
- 5.2.3 Operating Principles 42
- Redundancy Paralleling 42
- 5.2.4 Operation Modes Summary 42
- 5.3.2 Cabinet Installation 43
- 5.3.3 Preliminary Checks 43
- 5.3.4 Power Cables 43
- 5.3.5 Parallel Control Cables 43
- Auxiliary Dry Contact Cables 44
- 6.0 UPS SPECIFICATIONS 46
- Table 8 UPS terminal 47
- 6.4.1 Input Rectifier 48
- 6.4.2 DC Intermediate Circuit 49
- 6.4.3 Inverter Output 50
- 6.4.4 Bypass Input 50
- 7.2 Maintenance Mode 52
- 7.3 Locating the Cabinet 52
- 7.4 Cable Installation 52
- 7.4.3 Input/Output Wiring 53
- Isolation 55
- Transformer 55
- Wiring Legend 55
- 7.5 Bolting Cabinets Together 59
- 47" cabinet 60
- NSTALLATION DRAWINGS 61
- U3819205 62
- Source: U3819611, Rev. 0 63
- Source: U3819621, Rev. 1 64
- Installation Drawings 65
- 56 Liebert 66
- FRONT VIEW LEFT VIEW 67
- Front of UPS 68
- BOTTOM VIEW 68
- TOP VIEW 68
- DETAIL A 70
- (8.83") 71
- 62 Liebert 72
- DETAIL B 73
- 64 Liebert 74
- Detail B 75
- Top View 75
- (without BCB Cover Plate) 75
- Detail A 75
- Right Side 78
- 70 Liebert 80
- Without Covers 81
- 72 Liebert 82
- With Door Open 84
- Door Open 85
- 76 Liebert 86
- 9.0 OPERATION 87
- 9.1.1 Bypass Supplies 88
- 9.1.2 Operating Modes 88
- Normal Mode 88
- Battery Mode 88
- Bypass Mode 88
- Maintenance Mode 89
- Eco Mode 89
- 10.1 Operator Control Panel 90
- 10.2 Mimic Display Indicators 91
- 10.3 Control Buttons 92
- 10.4 Audible Buzzer 93
- 10.5 LCD Overview 93
- 10.6 Navigation Keys 94
- 10.7 UPS System Information 94
- 10.8 LCD Menus and Data Items 95
- Figure 58 Menu tree 96
- 10.9 Language Selection 98
- 10.10 Current Date and Time 98
- Figure 60 Set date and time 99
- 10.11 UPS Status Messages 100
- 10.12 Types of LCD Screens 101
- 10.12.3UPS Help Screen 102
- 10.12.4Screen Saver Window 102
- 10.13 Pop-Up Windows 103
- 11.0 OPERATING INSTRUCTIONS 104
- 11.2 UPS Startup 105
- F2 F4F1 F3 HELP 106
- Operating Instructions 107
- 98 Liebert 108
- 100 Liebert 110
- 11.7 Auto Restart 111
- 11.10 Battery Protection 112
- 11.13 Parallel System Startup 115
- 12.0 OPTIONS 116
- 12.1.5 Configuring Baud Rates 117
- Relay Card 118
- 12.3 Replacing Dust Filters 119
- 13.4 Battery Run Times 124
- 116 Liebert 126
- PPENDIX A-UPS STATUS MESSAGES 127
- Table 49 UPS status messages 128
- Technical Support / Service 132
- Locations 132
Related products and manuals for Uninterruptible power supplies (UPSs) Emerson Liebert NX
(28 pages)© 2020, manymanuals.com. All rights reserved. | 0.882 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals