Emerson Liebert NX User Manual Page 24
- Page / 132
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
Electrical Connections
14 Liebert
®
NX
™
3.1.2 UPS Input Configuration
Figure 3 illustrates the Liebert NX in a split bypass (dual-input) configuration. In this configuration,
the Static Bypass and the Maintenance Bypass lines are supplied from a separate feed from the Main
input. Both sources must be protected externally with properly sized protective devices. By default,
the unit ships with internal links installed between the bypass input and main input (Single Input
configuration). To wire the unit as a dual input UPS, remove the links and wire the bypass to the
input bus bars, then wire the main input directly to CB1 (see Figure 3).
Figure 3 Single module block diagram—dual input configuration
3.1.3 Cabling Guidelines
The following are guidelines only and are superseded by local regulations and codes of practice where
applicable. Use wiring rated at 75°C or greater.
1. The ground conductor should be sized in accordance with the input overcurrent protection device
data in Table 8. The ground cable connecting the UPS to the main ground system must follow the
most direct route possible. Control wiring and power wiring must be run in separate conduit.
Output and input cables must be run in separate conduit.
2. Consider using paralleled smaller cables for heavy currents—this can ease installation.
3. When sizing battery cables, a maximum voltage drop of 4VDC is permissible at the current
ratings in UPS terminal. For terminal connection sizing, see Table 8.
4. In most installations, especially parallel multi-module systems, the load equipment is connected
to a distribution network of individually protected busbars fed by the UPS output, rather than
connected directly to the UPS itself. When this is the case, the UPS output cables can be rated to
suit the individual distribution network demands rather than being fully load-rated.
5. When laying power cables, do not form coils; this will help avoid increasing formation of
electromagnetic interference.
NOTE
If more load is added to the distribution panel, the unit’s cabling must be resized.
3-Phase
3W + Gnd
3-Phase
3W + Gnd
AC Input
AC Output
3-Phase
3W + Gnd
Battery Cabinet
2W + Gnd
UPS Cabinet
Converter
InverterRectifier
Static Bypass
Internal Maintenance Bypass
- 2
- TABLE OF CONTENTS 3
- 7.0 LIEBERT BDC 4
- SAVE THESE INSTRUCTIONS 11
- 2Liebert 12
- Battery Cabinet Precautions 13
- 4Liebert 14
- GLOSSARY OF SYMBOLS 15
- 1.0 INTRODUCTION 16
- 2.0 INSTALLATION 17
- 2.3 Preliminary Checks 18
- 2.4 UPS Location 18
- Battery Location 19
- Final Position 19
- 2.6 Mechanical Considerations 20
- 2.6.4 Optional Cabinets 21
- Installation 22
- 12 Liebert 22
- 3.0 ELECTRICAL CONNECTIONS 23
- 3.1.2 UPS Input Configuration 24
- 3.1.3 Cabling Guidelines 24
- 3.1.4 Cable Connections 25
- 3.1.5 Safety Ground 25
- 3.1.6 Protective Devices 25
- 3.1.7 Cabling Procedure 26
- Common Input Connections 26
- Dual Input Connections 26
- Frequency Converter Mode 27
- 3.2 Control Cables 28
- 3.3 Dry Contacts 30
- 3.3.4 Output Dry Contacts 31
- EPO - NO 32
- EPO - NC 32
- 4.0 BATTERY INSTALLATION 33
- 4.3.1 Battery Cabinets 34
- 4.4 Non-Standard Batteries 36
- 4.5 BCB Shunt Trip 37
- 5.0 OPTIONS 38
- LBS Cable 39
- 5.2.1 General 40
- 480V, 3W 41
- System Input 41
- System Output 41
- 5.2.3 Operating Principles 42
- Redundancy Paralleling 42
- 5.2.4 Operation Modes Summary 42
- 5.3.2 Cabinet Installation 43
- 5.3.3 Preliminary Checks 43
- 5.3.4 Power Cables 43
- 5.3.5 Parallel Control Cables 43
- Auxiliary Dry Contact Cables 44
- 6.0 UPS SPECIFICATIONS 46
- Table 8 UPS terminal 47
- 6.4.1 Input Rectifier 48
- 6.4.2 DC Intermediate Circuit 49
- 6.4.3 Inverter Output 50
- 6.4.4 Bypass Input 50
- 7.2 Maintenance Mode 52
- 7.3 Locating the Cabinet 52
- 7.4 Cable Installation 52
- 7.4.3 Input/Output Wiring 53
- Isolation 55
- Transformer 55
- Wiring Legend 55
- 7.5 Bolting Cabinets Together 59
- 47" cabinet 60
- NSTALLATION DRAWINGS 61
- U3819205 62
- Source: U3819611, Rev. 0 63
- Source: U3819621, Rev. 1 64
- Installation Drawings 65
- 56 Liebert 66
- FRONT VIEW LEFT VIEW 67
- Front of UPS 68
- BOTTOM VIEW 68
- TOP VIEW 68
- DETAIL A 70
- (8.83") 71
- 62 Liebert 72
- DETAIL B 73
- 64 Liebert 74
- Detail B 75
- Top View 75
- (without BCB Cover Plate) 75
- Detail A 75
- Right Side 78
- 70 Liebert 80
- Without Covers 81
- 72 Liebert 82
- With Door Open 84
- Door Open 85
- 76 Liebert 86
- 9.0 OPERATION 87
- 9.1.1 Bypass Supplies 88
- 9.1.2 Operating Modes 88
- Normal Mode 88
- Battery Mode 88
- Bypass Mode 88
- Maintenance Mode 89
- Eco Mode 89
- 10.1 Operator Control Panel 90
- 10.2 Mimic Display Indicators 91
- 10.3 Control Buttons 92
- 10.4 Audible Buzzer 93
- 10.5 LCD Overview 93
- 10.6 Navigation Keys 94
- 10.7 UPS System Information 94
- 10.8 LCD Menus and Data Items 95
- Figure 58 Menu tree 96
- 10.9 Language Selection 98
- 10.10 Current Date and Time 98
- Figure 60 Set date and time 99
- 10.11 UPS Status Messages 100
- 10.12 Types of LCD Screens 101
- 10.12.3UPS Help Screen 102
- 10.12.4Screen Saver Window 102
- 10.13 Pop-Up Windows 103
- 11.0 OPERATING INSTRUCTIONS 104
- 11.2 UPS Startup 105
- F2 F4F1 F3 HELP 106
- Operating Instructions 107
- 98 Liebert 108
- 100 Liebert 110
- 11.7 Auto Restart 111
- 11.10 Battery Protection 112
- 11.13 Parallel System Startup 115
- 12.0 OPTIONS 116
- 12.1.5 Configuring Baud Rates 117
- Relay Card 118
- 12.3 Replacing Dust Filters 119
- 13.4 Battery Run Times 124
- 116 Liebert 126
- PPENDIX A-UPS STATUS MESSAGES 127
- Table 49 UPS status messages 128
- Technical Support / Service 132
- Locations 132
Related products and manuals for Uninterruptible power supplies (UPSs) Emerson Liebert NX
(28 pages)© 2020, manymanuals.com. All rights reserved. | 0.169 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals