Emerson MONITORING OpenComms User Manual

User ManualEnglishOpenComms Web Card

Network Interface MenuSelecting Option "2" from the Main Menu opens the Network InterfaceMenu.Network Interface Menu-----------------------1

Select option "2" to change Boot mode settings of the card.Valid Selections: ------------------ 1. Static 2. BootP 3. DHCPSelect Boot Mod

SNMP Communication MenuLiebert Network Interface CardSNMP Communications Menu-------------------------1: Authentication Traps 'no&apo

The options "a" "d" and "e" allow you to manage your list of networkdevices with access to the card. These options can

The options "a" "d" and "e" allow you to manage you list of networkdevices that will receive SNMP Traps from the card.

Web Server MenuWeb Server Menu----------------1: Web Server 'enabled'2: Change Username/Password<ESC>: Cancel menu levelPlease sel

Firmware Updates MenuFirmware Updates Menu----------------------1: Initiate XMODEM session...<ESC>: Cancel menu levelPlease select a key ?>Se

Factory Settings MenuFactory Settings Menu----------------------1: Reset to Factory Defaults Manufacture Date OCT 27,2000 MAC Address

Opening a Web ConnectionThis section explains the Web interface in detail. From the Web, you canmonitor and control the UPS in which the card is inst

You will notice that information on the Web page is grouped in Tabs andFolders. The card organizes similar information together in folders, andsimila

CONTENTSABOUT THIS USER MANUALQUICK START GUIDEINTRODUCTIONINSTALLATIONInstalling the CardConnecting the Card to the NetworkConfiguring the CardSERVIC

Connected Device InformationClicking between the monitor, contol, configure, and support tabs givesyou access to folder lists on the bottom of the lef

SecurityBy opening a connection to the OpenComms Web Card, you are able todo three things. You can Monitor, Configure and Control the UPS. The card

Monitor TabWhen you select the monitor tab, you are presented with ConnectedDevice: and Connected Device Status: on the top of the left pane. TheFold

Clicking on the Battery, Output, Input, Bypass (not supported in Power-Sure Interactive UPSs), or Internals folder replaces the summary datapresented

Control TabWhen you select the control tab, you are presented with ConnectedDevice: and Connected Device Status: on the top of the left pane. TheFold

Configure TabWhen you select the configure tab, you are presented with ConnectedDevice: and Connected Device Status: on the top of the left pane. The

SNMPClicking on the SNMP folder allows you to enable authentication traps.Clicking on the Access or Traps folder allows you to configure the devicesyo

Configure Tab - Making and Saving ConfigurationsSimilar to configuring the card using the Service Terminal, every time youmake a configuration change,

Configure Tab - After ReinitializationOnce card reinitialization is selected and confirmed, the card is unavail-able on the network. As the card reb

Support TabWhen you select the support tab, you are presented with ConnectedDevice: and Connected Device Status: on the top of the left pane. A sin-g

ABOUT THIS USER MANUALWelcome to the User Manual for the OpenComms Web Card. This man-ual is available from Liebert's web site at www.liebert.co

The OpenComms Web Card utilizes a SNMPv1 agent and is MIB-II com-pliant. The card supports the open standard UPS MIB RFC1628, withadditional function

MultiLink SupportThe most frequently asked question about configuring MultiLink to moni-tor a SNMP device, like the OpenComms Web Card, across the net

SL-52610 (9/02) Rev.2

CONFIGURE! Using a terminal emulation software package, like HyperTerminal™, open a direct connection to the card.BAUD RATE: 9600DATA BITS:

Worldwide SupportWorldwide FAX SupportU.S.A.U.K.FranceGermanyItalyNetherlandsE-mailWeb site+1 614-841-6755+1 614-841-67551-800 222-5877 +44 (0) 1628 4

Installing the CardThe OpenComms Web Card is hot swappable and user-serviceable.Although you do not need to turn off the UPS, disconnect any loads, or

Opening a Service Terminal ConnectionThis section covers the Service Terminal in detail. From the Service Ter-minal, you can configure all settings o

5. Press "Enter" to see the Main Menu.If you do not see the Main Menu, press "Enter" again several times. If theMain Menu fails t

Selecting Option "1" from the Main Menu opens the System InformationMenu.Liebert Network Interface CardSystem Information Menu--------------