Emerson DLC3020f Instruction Manual Page 170
- Page / 200
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
Instruction Manual
D103434X012
Blocks
November 2014
168
Table B‐54. Primary Transducer Block Parameter Definitions (Continued)
DescriptionInitial ValueRangeMode
RO /
RW
Index
Number
Label
PARAMETER_NAME
TIME_STAMP 67.3 RO NA NA
SUBCODE 67.4 RO NA NA
VALUE 67.5 RO NA NA
Data Type: Float
Value of parameter at alarm time for single
alarm, 0 for multiple alarms
Advise Priority
ADVISE_PRI
68 RW AUTO 0 to 15 2
Data Type: Uint8
Advise alert priority
Advice Enable
ADVISE_ENABLE
69 RW AUTO
1:
2:
3:
4:
5:
6:
7:
8:
2:
3:
6:
7:
8:
Data Type: BIT_ENUM (4)
Advise alert enable. Enable allows detection of
alert. All alerts can be disabled.
Advise Suppress
ADVISE_MASK
70 RW AUTO
1:
2:
3:
4:
5:
6:
7:
8:
All 0
Data Type: BIT_ENUM (4)
Advise alert mask. MASK controls whether an
alert is reported. If alert is enabled the alert
condition is evaluated and the ACTIVE
parameter is updated reflect if alert is active or
not. If the bit is set reporting is suppressed.
Advise Active
ADVISE_ACTIVE
71 *RO
1:
2:
3:
4:
5:
6:
7:
8:
All 0
Data Type: BIT_ENUM (4)
Advise Alert Status
0 = inactive, 1 = active
Advise Alarm
ADVISE_ALM
72
Data Type: DS‐71
Used to report alerts to host system.
UNACKNOWLEDGED 72.1 RW AUTO
0: Undefined
1: Acknowledged
2: Unacknowledged
0
ALARM_STATE 72.2 RO NA
0: Undefined
1: Clear (reported)
2: Clear (not reported)
3: Active (reported)
4: Active (not reported)
0
TIME_STAMP 72.3 RO NA NA 0
SUBCODE 72.4 RO NA NA 0
VALUE 72.5 RO NA NA 0
Data Type: Float
Value of parameter at alarm time for single
alarm, 0 for multiple alarms
HEALTH_INDEX
73 RO NA 0 to 100 100
Data Type: Uint8
Represents overall health of device. 10% ‐ Failed
Alert is active, 60% ‐ Maintenance Alert is active,
90% ‐ Advisory Alert is active, 100% no alerts are
active.
PWA_SIMULATE 74 *RO AUTO
1: Simulate Off
2: Simulate Enabled
1: Simulation off
Data Type: Enum (1)
When this is set to 2 all the alert ACTIVE
parameters can be written, except for
DETAILED_STATUS. This allows alerts to be
simulated for testing with hosts.
*RW when simulate jumper is jumpered
RAPID_RATE_LIMIT 75 RW AUTO
Lower limit: 1% of
displacer length.
Upper limit: displacer
length.
1.778 cm
The maximum amount of fall/rise in level before
the rapid fall/rise alerts activate per second.
-Continued-
- FIELDVUE 1
- DLC3020f Digital Level 1
- Controller for F 1
- fieldbus 1
- Contents 3
- Scope of Manual 5
- Instrument Description 5
- Foundation Fieldbus Blocks 5
- Using This Manual 6
- Specifications 7
- Related Information 7
- Educational Services 7
- Instruction Manual 10
- 28B5536‐1 11
- Section 2 Installation2‐2‐ 13
- Lever Lock 14
- Mounting 15
- DLC3020f Orientation 16
- 20A7423‐C 18
- DIGITAL LEVEL CONTROLLER 18
- AMBIENT TEMPERATURE (_C) 19
- STANDARD TRANSMITTER 19
- 39A4070‐B 19
- Fieldbus Connections 20
- Simulate Enable Jumper 21
- GE46500‐B 22
- Section 3 Overview3‐3‐ 23
- Primary Purpose Variables 24
- Shortcuts 24
- Section 4 Configuration4‐4‐ 27
- Manual Setup 28
- Variable Configuration 29
- Sensor Limits 29
- Sensor Hardware Information 30
- Sensor Units 30
- Sensor Parameters 31
- Torque Tube 32
- Process Fluid 33
- Temperature Compensation 33
- View Fluid Density Table 34
- Display Option 34
- Decimal Places 34
- Display Primary Value Offset 35
- Scrolling Message Control 35
- Snap Acting Control 35
- Primary Value 35
- Primary Value Percent 36
- DI1 Trip Point Settings 36
- DI2 Trip Point Settings 36
- Write Alarm 37
- Block Alarm 37
- Write Lock 37
- Confirm Time 38
- Communication Timeout 38
- Function Block Available 38
- Transducer Block 39
- Features Selected 39
- Alert Key 39
- Maximum Alerts Allowed 39
- Alert Setup 40
- PlantWeb Alerts 41
- Electronics 41
- Operational 41
- Rate Limit 41
- Calibration in Use 43
- Calibrate Instrument 44
- Full Calibration 45
- Trim Current Calibration 46
- Alert Conditions 47
- Variables 48
- Run Time Extremes 49
- Simulate 50
- Calibration Setup/Logs 51
- Instrument Display Test 52
- Restart Device 52
- Tools Required 53
- LCD Meter Assembly 55
- Removing the LCD Meter 56
- Replacing the LCD Meter 56
- Electronics Module 57
- Terminal Box 58
- Assembly 59
- Lever Assembly 60
- Packing for Shipment 61
- Instrument Troubleshooting 62
- Section 8 Parts8‐8‐ 65
- Parts Kits 66
- Parts List 66
- Transducer Assembly 68
- (figure 8‐2) 68
- Terminal Box Assembly 69
- (figure 8‐3) 69
- Terminal Box Cover Assembly 69
- (figure 8‐4) 69
- 28B5741‐B 70
- 29B8444‐A 71
- 29B8445 B 71
- Yamatake NQP Sensor 72
- Foxboro‐Eckardt Sensors 72
- 249 SENSOR (SIDE VIEW) 73
- FIELDBUS‐FBUS_31A 75
- FIELDBUS‐FBUS_03A 77
- Signal Conversion 78
- Advanced Features 79
- AI Block Parameter List 81
- TRANSDUCER_STATUS 9.3 RO 0 82
- UNACKNOWLEDGED 22.2 RO ALL 83
- PID Function Block 87
- Filtering 90
- Feedforward Calculation 91
- Output Tracking 91
- Set Point Tracking 91
- Reverse and Direct Action 92
- PID Block Parameter List 94
- 3=Active reported 97
- 4=Active not reported 97
- Unacknowledged 100
- T_AUTO_HYSTERESIS 101
- View Lists 102
- Status Handling 107
- I/O Selection 107
- Block Initialization 107
- Field Value Processing 108
- Alarm Detection 108
- Block Errors 109
- Action on Failure 109
- Simulation 109
- Mode Handling 116
- Shed With Return Options 117
- Shed With No Return Options 117
- Setting the Output 118
- Action On Fault Detection 119
- I/O Options 120
- Application Information 121
- CAP_STDDEV 125
- Limit Propagation 130
- Substatus Propagation 130
- STATUS_OPTS Supported 130
- SELECT_TYPE Must 132
- Input Selection 133
- Supported Modes 143
- Block Execution 144
- Advanced Topics 146
- Troubleshooting 148
- Resource Block 152
- AUTO 0 to 65535 0 159
- AUTO 1 to 255 1 159
- AUTO 3:AUTO 159
- AUTO 0 to 15 2 168
- Transducer Block (LCD) 174
- Function Block Overview 181
- Resource Blocks 182
- Transducer Blocks 182
- Block Modes 183
- Explanation of Modes 184
- Device Descriptions 185
- Status Propagation 186
- Network Communication 187
- Scheduled Transfers 188
- Unscheduled Transfers 189
- Network Management 190
- Glossary 191
- D103434X012 192
- November 2014 192
Related products and manuals for Measuring, testing & control Emerson DLC3020f
(35 pages)
(3 pages)Reliance Water Heaters 184735-000 podręczniki
Instrukcje obsługi i podręczniki użytkownika dla Grzejniki wodne i kotły Reliance Water Heaters 184735-000.
Dostarczamy 1 pdf podręczników Reliance Water Heaters 184735-000 do pobrania za darmo według typów dokumentów: Instrukcja Obsługi
Comments to this Manuals