Emerson EM-262 User Manual download pdf

O Owner's Manual O Location of controls

4. Set your mobile phone to search for Bluetooth devices.

©Bluetooth'*

Wireless Headset

Model: EM262

^ In the box

8a About noise cancellation technology

This headset uses a Dual Microphone Design to filter out

wind and unwanted external noise.

Using Noise Cancellation technology, the headset compares

the sound from the twin built-in microphones, and is able to

recognize the difference between voice and unwanted

background noise. ^ ^ .

Dual Microphone Design

Wind and unwanted bacl^round noise

are filtered out enabling the other end of

your conversation to hear you clearlyl

Microphone 2

Power button

Power ON/OFF

Answer/end

Indicator light

Charging

Volume up

Volume down

Microphone 2 ^Microphone 1

within 3 feet

Bluetooth: Enabled

Paired Devices:

‘Empty ’

Charging the Bluetooth Headset

Before using your Bluetooth Headset for the first time, charge

it for 10-12 hours.

1. Connect the smaller end of the USB cable to the charging

socket of the headset.

2. Connect the other end of the USB cable to either the:

• AC Charger, and plug into a wall (A/C) outlet.

• Computer's USB port.

• Car Charger

3. The BLUE LED indicator light turns on.

4. The BLUE LED indicator light shuts off when the headset

is fully charged (approximately 2-3 hours).

NOTE: The Bluetooth Headset will emit an intermittent

beep tone when the battery is running low and requires

recharging.

5. When the phone finds the headset, confirm by selecting it

from the list.

Bluetxioth: Enabled

Paired Devices:

6. Enter passcode"0000"when prompted by the phone.

Bluetooth: Enabled

Paired Devices:

Enter numeric passkey

for EM262:

NOTE: Make sure you charge your headset for 10-12 hours

before using it for the first time.

^ Pairing the heaebetwith a Bluetooth enabled phone

1. Make sure the Bluetooth Headset is turned off.

2. Keep your Bluetooth Headset and mobile phone within 3

feet of each other during the pairing process.

3. Press and HOLD the [POWER] button until the BLUE indicator

light turns on, flashes several times, and becomes a steady

blue. The headset is now in Pairing Mode, and is ready to

connect to your mobile phone.

Power button

(Press & HOLD)

Indicator light

Confirm connection to

EM2B2?

YES I/

8. When attempting to reconnect the headset to your mobile

phone,you may see the message below, and your mobile

phone will prompt you to accept the connection request to

the EM262 headset, and an option not to ask this again.

Please accept the connection,and if you select"Don't ask this

again" your phone will automatically accept future connection

requests from your Bluetooth Headset.

Bluetooth: Enabled

Paired Devices:

Accept connection request

from EM2B2?

YES

B Don't ask this again

NOTE: To enter the Pairing Mode,you must press and HOLD the

power button for approximately 10 seconds.

Microphone 1

NOTE: The screenshots above are typical of many Bluetooth enabled

phones in the market today, and are used to assist in the

explanation of the pairing process. Your mobile phone's

interface and interaction with the Bluetooth Headset may

slightly differ from the illustrations above.

8M Using your Bluetooth Headset

Powering ON/OFF

• To turn ON, press and HOLD the [POWER] button until the

BLUE LED indicator light turns on.

• To turn OFF, press and HOLD the [POWER] button until the

BLUE LED indicator light flashes quickly several times, and

then turns off.

Power button

(Press & HOLD)

Indicator light

Answering/Ending a call

• To answer a call, press and release the [POWER] button.

• To end a call, press and release the [POWER] button.

Power button

NOTE: If your mobile phone is Bluetooth 2.1 compliant, you will

not need to enter a passcode, and can skip to step 7.

7. Your mobile phone will confirm that the pairing was completed,

and prompt you to accept the connection. Please respond

YES to connect the headset to your mobile phone. If the pain ng

was successful, the headset's indicator light flashes a steady blue.

Bluetooth: Enabled

Paired Devices:

To make a call

Dial the number and press the send button on your mobile

phone, the call is automatically transferred to the headset.

Redialing the iast number caiied (Dependent

on your phone supporting this feature)

Double press the [POWER] button and release. The headset

will emit a confirmation beep tone, and the last number

called will be redialed.

Power Button

Double Press to redial

Adjusting the voiume

Press the [VOLUME UP] or [VOLUME DOWN] button to adjust

the volume to the desired level.

Volume up

NOTE: You may also adjust the volume from your mobile phone's

volume control.

8M Wearing your Bluetooth Headset

You may wear your headset with or without the provided

earhook. If you choose to wear your headset with the earhook,

connect it to the headset as shown in the diagram below.

Earhook

comfortably

Headset on the same side ofthe body as your mobile phone

8Ba Troubleshooting tips

I cannot get the Bluetooth Headset into Pairing Mode

• Make sure the Bluetooth Headset is turned off before

beginning the pairing process.

• Press and HOLD the [POWER] button until the BLUE

indicator light turns on,flashes several times, and becomes a

steady blue. This will signal that the headset is in Pairing

Mode,and ready to connect to your mobile phone.

Mymobile phone is not able to pairwith the Bluetooth Headset

• Make sure that you fully charged the headset before pairing.

• Keep your Bluetooth Headset and mobile phone within 3

feet of each other during the pairing process.

• Check that your phone's Bluetooth feature is turned ON.

• Try repeating the pairing process, see "Pairing the headset

with a Bluetooth enabled phone."

Headset, when I shut my phone and turn it on again, my

^ headset did not automatically connect_____________________y

' Try turning the headset OFF, and then turning it ON again.

' Many mobile phones have an auto reconnect option when first

attempting to reconnect to a newly paired Bluetooth device.

Make sure you accept this option, so that your Bluetooth Headset

automatically reconnects to your mobile phone; check the user

guide of your mobile phone for more information regarding

this option.

' Try unpairing the headset from your phon^and repeat the pa i ri ng

procedure

I hear distortion, and the sound quality is poor

For the best audio quality, always wear your Bluetooth Headset

on the same side of the body as your mobile phone.

Check that the battery is charged enough.

^^The sound is very low

Try adjusting the volume by using the [Volume] button on your

headset; make sure the volume on your mobile phone is

turned up as well.

Drive Safe

Driving while talking on your mobile phone is dangerous,and

illegal in many states.

Although this device enables drivers to conduct handsfree

conversations, it is still dangerous to drive and use a mobile phone

at the same time.

We recommend pulling over before making or answering calls,

especially during adverse driving conditions. Please use your

mobile phone,and our product responsibly while driving!

8Bd Safety information

• Check local laws regarding use of a mobile handset and wireless

headset while driving. If you use the Bluetooth Headset while

drivi ng, ensure your attention and focus remains on your driving.

* Observe all signs in the designated areas where some electronic

devices or RF radio products are required to be switched off.

These could include airplanes, hospitals,blasting areas,and

potentially explosive atmospheres.

CAUTION: Although this device enables drivers to

conduct handsfree conversations, it is still dangerous

to drive and use a mobile phone at the same time.

Always keep your full attention on your driving.

1^ Product maintenance

• Power off this product when not in use.

• DO NOT expose this product to water or other liquids.

• DONOTuseabrasivedeaningsolventstodeantheBluetoothHeadset

• If you will not use the Bluetooth Headset for long periods^ be sure to

store it in a dry plac^fieefiom extreme temperature humidity and dust

FCC and telephone company information

FCC Part 15

This equipment has been tested and found to comply with the

requirements for a Class B digital device under Part 15 of the

Federal Communications Commission (FCC) rules. These

requirements are intended to provide reasonable protection

against harmful interference in a residential installation. This

equipment generates, uses and can radiate radio frequency energy

and, if not installed and used in accordance with the instructions,

may cause harmful interference to radio communications. However,

there is no guarantee that interference will not occur in a particular

installation. If this equipment does cause harmful interference to

radio or television reception, which can be determined by turning

the equipment off and on, the user is encouraged to try to correct

the interference by one or more ofthe following measures:

• Re-orient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different

from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

Do not attempt to repair or modify this equipment.

Warning: Changes or modifications to this equipment not

expressly approved by the party responsible for compliance

could void the user's authority to operate the equipment.

8Ba Industry Canada

Operation is subject to the following two conditions: (1) This

device may not cause interference and (2) This device must

accept any interference, including interference that may

cause undesired operation ofthe device.

The term "1C:" before the certification/registration number

only signifies that registration was performed based on a

Declaration of Conformity indicating that Industry Canada

technical specifications were met. It does not imply that

Industry Canada approved the equipment.

8M Warranty information

Limited Warranty

In the unlikely event that this product is defective, or does

not perform properly, you may within one (1) year from

your original date of purchase return it to the authorized

service center for repair or exchange.

TO OBTAIN WARRANTY SERVICE:

• Provide proof of the date of purchase within the package

(Dated bili of saie).

• Prepay aii shipping costs to the authorized service center,

and remember to insure your return.

• Include a return shipping address (no P.O. Boxes),

a telephone contact number, and the defective unit within

the package.

• Describe the defect or reason you are returning the product

Your product will be repaired or replaced, at our option, for the same

or similar model of equal value if examination by the sen/ice center

determines this product is defective. Products received damaged

as a result of shipping will require you to file a claim with the carrier.

The shipping address ofthe authorized service center is:

^ Southern Telecom Inc.

ATTN: Returns Department

14-C 53rd Street

Brooklyn, NY 11232

Should you have any questions or problems concerning this

product, please contact our customer service department at:

01-877-768-8483 (Toll Free)

Monday - Thursday: 9AM - 5PM (EST)

Friday: 9AM-3PM (EST)

via e-maii at

Q [email protected]

Warranty service not provided

This warranty does not cover damage resulting from accident,

misuse, abuse, improper installation or operation, lack of reasonable

care, and unauthorized modification. This warranty is voided in

the event any unauthorized person opens, alters or repairs this

product. All products being returned to the authorized service

center for repair must be suitably packaged.

Limitation of Warranty:

• THE WARRANTY STATED ABOVE IS THE ONLY WARRANTY

APPLICABLE TO THIS PRODUCT. ALL OTHER WARRANTIES,

EXPRESS OR IMPLIED (INCLUDING ALL IMPLIED WARRANTIES OF

MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE) ARE

HEREBY DISCLAIMED. NO VERBAL OR WRITTEN INFORMATION

GIVEN BY SOLITHERN TELECOM INC. ITS AGENTS, OR EMPLOYEES

SHALL CREATE A GUARANTY OR IN ANY WAY INCREASE THE

SCOPE OF THIS WARRANTY.

• REPAIROR REPLACEMENT AS PROVIDED UNDER THIS WARRANTY

IS THE EXCLUSIVE REMEDY OF THE CONSUMER. SOUTHERN

TELECOM INC. SHALL NOT BE LIABLE FOR INCIDENTAL OR

CONSEQUENTIAL DAMAGES RESULTING FROM THE USE OF THIS

PRODUCT OR ARISING OUT OF ANY BREACH OF ANY EXPRESS

OR IMPLIED WARRANTY ON THIS PRODUCT. THIS DISCLAIMER

OF WARRANTIES AND LIMITED WARRANTY ARE GOVERNED

BY THE LAWS OF THE STATE OF NEW YORK. EXCEPT TO THE

EXTENT PROHIBFTED BYAPPUCABLE LAW, ANYIMPUEDWARRANTY

OF MERCHANTABILFTY OR FTTNESS FOR A PARTICULAR PURPOSE

ON THIS PRODUCT IS LIMITED TO THE APPLICABLE WARRANTY

PERIOD SET FORTH ABOVE.

Some states do not allow the exclusion nor limitation of incidental

or consequential damages, or limitations on how long an implied

warranty lasts so the above limitations or exclusions may not apply

to you. This warranty gives you specific legal rights, and you also may

have other rights that vary from state to state.

Distributed by: AIT Inc. Brooklyn, NY 11232

www.emersonphones.com

Emerson and the G-Clef logo are registered trademarks of

Emerson Radio Corp. Parsippany, New Jersey USA.

Tire Bluetooth^’v\/ord markand logos are owned by the Bluetooth SIG, Inc

©Bluetooth'* 1
Wireless Headset 1

Summary of Contents

Page 1 - Wireless Headset

O Owner's Manual O Location of controls4. Set your mobile phone to search for Bluetooth devices.TM©Bluetooth'* Wireless HeadsetModel: EM262^

Comments to this Manuals

No comments

Emerson EM-262 User Manual

Browse online or download User Manual for Wireless Headsets Emerson EM-262. Emerson EM-262 User Manual

Summary of Contents

Comments to this Manuals