Islatrol
™
IE Series
Active Tracking Filter
™
Shunt Absorbing Components
load side sine wave tracking circuitry
Form C Relay Contacts
normally open and normally closed dry
contact for remote status monitoring
MOV Array
high-energy surge current diversion
array providing transient protection
line to neutral, line to ground, and
neutral to ground
Series Blocking Inductor
voltage blocking current
soothing inductor
DIN Rail Mountable
mounts to standard 35 mm
industrial DIN rail; rotates 90°
for mounting flexibility
Shunt Absorbing Components
line side sine wave tracking circuitry
Unit Status Indicator
green LED monitors the operational
status of the Elite Series
Finger Safe Terminals
IEC 998 approved terminals
Silicon Avalanche Diodes
fast responding surge current
diversion components
Pulse Capacitor
high-frequency noise absorption
System Design
Connection Diagram
Filtering/Line Conditioning
7
Data/Signal Line Protection
18
Technology Three-Stage Series Hybrid
Input Voltage 120 VAC 50/60 Hz
Output Current 15 Amps Max.
Response Time <5 Nanoseconds
Maximum Surge Current (8x20 µs) 10 kA
Occurrences at 500 Amps >50
Parameter Normal Mode Common Mode
(L-N) (L-G) (N-G)
IEEE 587 CAT A Ring* 172 V 280 V
IEEE 587 CAT B Ring* 205 V 280 V
IEEE 587 CAT B Impulse* 330 V 360 V
*Measured from zero volts, 90° Phase angle
Signal Protector Technology GDT, PTC, SAD
AC Protector Technology MOV, Fuse
Peak Surge Current 10 kA
Response Time <1 Nanosecond
Voltage Clamp (customer selected) 8–200 Volts
Series Resistance 5 ! (Typical)
NEMA-4X
Glass-Filled Polycarbonate Base
Cover Molded in Clear Polycarbonate
Knockouts for 1/2" and 3/4" hubs
Bosses for 6 BZ x 3/8" Self-Tapping Screws
Maximum Protection—Total Insulation
Corrosion Resistant
Resists Temperature of 248°F
Flammability Rating UL94-5V
Nominal Outside dimensions (Inches)
H= 6.89, W=6.89, D=2.95
Edco
™
SLAC Series
AC Power/Signal
The Edco
™
SLAC Series suppressor is specifically designed to protect electronic
instruments used by the water/wastewater industries. It combines hybrid AC
power protection and signal line protection in a NEMA-4X polycarbonate case.
The AC power suppressor can supply up to 1875 Watts and has a 15 Amp
replaceable fuse to prevent overloading of the protective elements. A “Power
ON” LED provides visual indication that power is applied to instruments. Signal
line protection is accomplished by the Edco
™
PC642 Series available in a variety
of voltage clamps. Signal current can be monitored by reading the voltage
across the 10 V, 1% resistors (TP1 & TP2 or TP3 & TP4). All leads going to the
Edco
™
SLAC board are terminated by quick disconnect or barrier block
connectors to facilitate easy removal for service or replacement.
Features
■ Optional twist lock plug lightning & surge
suppression for AC power and low-voltage
signal lines
■ Series hybrid AC suppressor/filter
■ Plug-in protection module
■ 15 Amp replaceable fuse
■ Test jacks for signal line monitoring
■ “Power ON” indicator
■ Optional stainless steel or fiberglass
enclosure
■ 5 year warranty
■ ANSI/UL 1449 Third Edition
General Technical Specifications
AC Power
General Technical Specifications
Signal Line
Standard Enclosure Optional Enclosure
Ordering Information
How to Specify the Appropriate Model
These blocks are for PC642
VoltageSelection if applicable. See
PC 642 Datasheet for additional
information. 0 3 6 L C is standard
for 4-20 mA Signal Line.
Comments to this Manuals