Emerson EWC1902 Service Manual Page 27
- Page / 92
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
1-7-6 T7300EA
The following 2 adjustments normally are not
attempted in the field. They should be done
only when replacing the CRT then adjust as a
preparation.
13.Purity Adjustment
Purpose: To obtain pure color.
Symptom of Misadjustment: If Color Purity Adjust-
ment is incorrect, large areas of color may not be
properly displayed.
* This becomes RED COLOR if push 7KEY with a
service mode.
1. Set the unit facing east.
2. Operate the unit for over 30 minutes before adjust-
ing.
3. Fully degauss the unit using an external degauss-
ing coil.
4. Set the unit to the AUX Mode which is located
before CH2 then input a red raster from video in.
5. Loosen the screw on the Deflection Yoke Clamper
and pull the Deflection Yoke back away from the
screen. (See Fig. 6.)
6. Loosen the Ring Lock and adjust the Purity Mag-
nets so that a red field is obtained at the center of
the screen. Tighten Ring Lock. (See Fig. 5,6.)
7. Slowly push the Deflection Yoke toward the bell of
the CRT and set it where a uniform red field is
obtained.
8. Tighten the clamp screw on the Deflection Yoke.
14. Convergence Adjustment
Purpose: To obtain proper convergence of red, green
and blue beams.
Symptom of Misadjustment: If Convergence Adjust-
ment is incorrect, the edge of white letters may have
color edges.
Test point Adj. Point Mode Input
---
Deflection Yoke
Purity Magnet
--- *Red Color
Tape M. EQ. Spec.
--- Pattern Generator See below.
Figure
BLUE
GREEN
RED
Fig. 5
Test point Adj. Point Mode Input
---
C.P. Magnet (RB),
C.P. Magnet (RB-G),
Deflection Yoke
---
Dot Pattern
or
Crosshatch
Tape M. EQ. Spec.
--- Pattern Generator See below.
Figure
DY WEDGE
DEFLECTION YOKE
C.P. MAGNET
RING LOCK
SCREW
SCREW
RB-GRB
PURITY
CRT
COIL
COIL CLAMPER
C.P. MAGNET CLAMPER
Fig. 6
Fig. 7
Fig. 8
B
G
R
R
G
B
C.P. MAGNET (RB)
RB
G
RB
G
C.P. MAGNET (RB-G)
- SERVICE MANUAL 1
- IMPORTANT SAFETY NOTICE 2
- MAIN SECTION 3
- SPECIFICATIONS 4
- <AUDIO> 5
- IMPORTANT SAFETY PRECAUTIONS 6
- Precautions during Servicing 8
- Safety Check after Servicing 9
- STANDARD NOTES FOR SERVICING 10
- Tweezers 11
- Soldering Iron 11
- Presolder 12
- Flat Pack-IC 12
- Instructions for Handling 13
- Semiconductors 13
- PREPARATION FOR SERVICING 14
- 1 92 3 4 5 6 7 8 15
- 1011 1412 15
- [1] Rear Cabinet 17
- [2] Tray Chassis 17
- [4] Main CBA 17
- [3] Deck Unit 17
- 1-6-2 T7300DC 18
- 1-6-3 T7300DC 19
- 1-6-4 T7300DC 20
- 1-6-5 T7300DC 21
- Fig. 1-1 22
- Remote control unit (Bottom) 22
- 3. TV AGC Adjustment 23
- 4-1. H Adjustment 23
- 4-2. C-Trap Adjustment 23
- 4-3. Y DL Time Adjustment 24
- 5. V. Size Adjustment 24
- 6. V. Shift Adjustment 24
- PATTERN GENERATOR 25
- RF INPUT 25
- 9. Sub-Brightness Adjustment 26
- 10. Focus Adjustment 26
- 12. CCS Text Box Location 26
- 13.Purity Adjustment 27
- 14. Convergence Adjustment 27
- BLOCK DIAGRAMS 29
- Video Block Diagram 30
- Audio Block Diagram 31
- Chroma/Tuner Block Diagram 32
- CRT/H.V. Block Diagram 33
- HOT COLD 34
- MECHANICAL TROUBLE INDICATOR 35
- Countermeasure for Mechanical 36
- Malfunction 36
- Repair method #1 37
- Repair method #2 38
- Repair method #3 38
- Repair method #4 38
- Standard Notes 39
- T7300SCM1 41
- 1-9-6 1-9-7 1-9-8 T7300SCM2 42
- T7300SCM3 43
- Main 4/4 Schematic Diagram 44
- Main CBA Top View 45
- Sensor CBA 45
- Top View 45
- (START-SENSOR) 45
- Main CBA Bottom View 46
- CRT CBA Top View 47
- CRT CBA Bottom View 47
- Z11WF1-10-1 1-10-2 48
- WIRING DIAGRAM 49
- SYSTEM CONTROL TIMING CHARTS 50
- IC PIN FUNCTION DESCRIPTIONS 52
- LEAD IDENTIFICATIONS 54
- DECK MECHANISM 55
- STANDARD MAINTENANCE 56
- A/C Head 57
- J-1-1, J-1-2 58
- Cam Gear 59
- LDG Belt (B) 59
- Incorrect 61
- Waveform 62
- Erase Head 62
- OF DECK MECHANISM 63
- [20],[23] 63
- Lead with 66
- Blue Stripe 66
- Lead with White Stripe 67
- Fig. DM11 68
- Fig. DM12 68
- Fig. DM14 69
- Fig. DM13 69
- Fig. DM15 70
- Fig. DM16 70
- Fig. DM17 70
- Fig. DM18 70
- Alignment 3 72
- Cam Gear (A), Rack Assembly 72
- EXPLODED VIEWS AND 73
- PARTS LIST SECTION 73
- EXPLODED VIEWS 74
- 3-1-3 T7300PEX 75
- DECK EXPLODED VIEWS 76
- Deck Mechanism View 2 77
- Deck Mechanism View 3 78
- MECHANICAL PARTS LIST 79
- CRT Warning Label 80
- CRT Type No 80
- ELECTRICAL PARTS LIST 81
- 20020205 3-3-2 T7300EL 82
- 20020205 3-3-3 T7300EL 83
- 20020205 3-3-4 T7300EL 84
- 20020205 3-3-5 T7300EL 85
- 20020205 3-3-6 T7300EL 86
- 20020205 3-3-7 T7300EL 87
- 20020205 3-3-8 T7300EL 88
- 20020205 3-3-9 T7300EL 89
- SENSOR CBA 90
- DECK PARTS LIST 91
- B359 CLEANER LEVER B361 91
- Type ID No. ID No 91
- A 0VM304413 0VM411114 91
- B 0VM305090 Not used 91
- Printed in Japan 92
- 2002-02-20 HO 92
© 2020, manymanuals.com. All rights reserved. | 1.105 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals